Unique board will control 6-Strobe LED's, 6-Fading LEDs, and 8-Switched On and Off LED's by remote activation.
Board has input connection for remote switching activation by relays, switches or controller board.
Each Switch Bank will control one effects section
LED Wire terminal blocks for quick connection
Board requires 9 Vdc @2 Amp Power supply



( Power supply, LED's not included )

Unique board will control 6-Beacon LED's, 10-Chasing LEDs by remote activation.
Board has input connection for remote switching activation by relays, switches
or controller board.
Each Switch Bank will control one effects section.
LED Wire terminal blocks for quick connection
Board requires 9 Vdc @2 Amp Power supply



( Power supply, LED's not included )

Unique board will control 24 LEDs by remote activation.
Board has input connection for remote switching activation by relays, switches or controller board.
Each Switch Bank will control 8 LED's, three switched banks available
LED Wire terminal blocks for quick connection
LED's require voltage drop resistance when connected to board.
Resistors not on control board.
Board requires 9 Vdc @2 Amp Power supply



( Power supply, LED's not included )

Unique board will control 3 High Intensity Luxeon LEDs by remote activation.
Board has input connection for remote switching activation by relays, switches or controller board.
Each Switch Bank will control one effects channel
LED Wire terminal blocks for quick connection
Board requires 9 Vdc @2 Amp Power supply
Board Power output per channel 3-5 Vdc


( Power supply, LED's not included )

Unique board will control 2-Channels Switched On and Off Power Driver's by remote switching activation. The two channels can be connected to any standard Lighting Wire strands.
Board has input connection for remote activation by relays, switches or controller board.
Each Switch Bank will control one effects section
LED Wire terminal blocks for quick connection
Board requires 9 Vdc @2 Amp Power supply



( Power supply, LED's not included )

Unique board will control 2-Channels Switched On and Off Power Driver's by remote switching activation. The two channels can be connected to any Fiberoptic Light source and fiberoptic cables.
Each Switch Bank will control one fiber section
Board has input connection for remote activation by relays, switches or controller board.
LED Wire terminal blocks for quick connection
Fiberoptic cable holders
Board requires 9 Vdc @2 Amp Power supply



( Power supply, LED's not included )

Unique board will control 3-Channels Switched On and Off Power by remote switching activation. The three channels can be connected to any Light source such as LED's, LUXEON LED's, Fiberoptics, DC Light Bulbs.
Each Switch Bank will control one effects section, each effects section can operate 2 outputs (6 total outputs available)
Board has input connection for remote activation by relays, switches or controller board.
LED Power Output determined by Input Power controlling board
LED Wire terminal blocks for quick connection
Board requires 9 Vdc @2 Amp Power supply



( Power supply, LED's not included )

This unique board will control eight Bi-Color LEDs and effects.

There are 3 modes of operation that can be selected. In Mode 1, the LEDs are strobed on and off. In Mode 2, the LEDs are faded on and off. In Mode 3, the LEDs are either full on or off. The color of the LEDs is selected by dry contact closure of the Remote Green LED Trigger or the Remote Red LED Trigger terminals. There is also an on-board pushbutton that can be used to select the LED color. In Modes 1 and 2, when both triggers are activated simultaneously, the colors jump back and forth (Red / Green). In Modes 1 and 2, the rates of strobing or fading can be adjusted by using the Mode 1 or Mode 2 speed potentiometers. The rates at which the colors jump back and forth in Modes 1 and 2 is determined by the on-board potentiometers

Board operates from 7-12 Vdc - Not Included

This unique board will allow the control of eight channels of remote DC lights (LED or incandescent) in 16 different lighting effects. Each channel is capable of driving up to 200 mA of lighting. An on-board LED for each channel indicates that the channel is active. A 16-Position Mode Selection switch allows the user to select which sequence will be active. The selected sequence will begin immediately upon power-up and will continue until the power is removed from the board. There are 2 potentiometers on the board that allow the user to control the rate of the selected sequence.
The board has an on-board On/Off switch and a terminal block that allows the connection of a remote On/Off switch. Power can be supplied to the board via the 2.1mm power connector or the adjacent terminal block. Power should be provided that is sufficient to drive the board and all of the eight light channels (~2A max). There are 2 SS relays on the board that activate as soon as power is supplied to the board also for driving sound effect boards, or controller boards.

Special Effect Operation:
Mode 1 ­ Marquee A: All channels start off. Channels 1 through 8 will then light up in sequence until all 8 channels are lit. Then all channels go off and then repeats.
Mode 2 ­ Marquee B: All channels start off. Channels 8 through 1 will then light up in sequence until all 8 channels are lit. Then all channels go off and then repeats (reverse of Mode 1).
Mode 3 ­ Marquee C: All channels start on. Then channels 1 through 8 will go off in sequence until all channels are off and then repeat.
Mode 4 ­ Marquee D: All channels start on. Then channels 8 through 1 will go off in sequence until all channels are off and then repeat (reverse of Mode 3).
Mode 5 ­ Cylon Effect: A single channel rasters back and forth.
Mode 6 ­ Reverse Cylon Effect: All channels are on with one channel being off that rasters back and forth (reverse of Mode 5).
Mode 7 ­ Knight Rider: All channels start off. Channels come on starting at channel 1 going to channel 8. When all channels are on, the channels begin turning off starting at channel 8 going down to channel 1.
Mode 8 ­ Strobe All: All channels strobe on and off in unison.
Mode 9 ­ Fade All: All channels will fade on and off in unison.
Mode 10 ­ Random Flash: Channels will flash randomly.
Mode 11 ­ Random Fade: Channels will randomly fade on and off.
Mode 12 ­ Heart Beat: All Channels will flash like a heartbeat. Rate Pot 1 will control the time between the 2 short flashes and Rate Pot 2 will control the overall rate of the heartbeat.
Mode 13 ­ Railroad Crossing Signal: Channels 1 ­ 4 and channels 5 ­ 8 will flash alternately.
Mode 14 ­ R2D2: Channels 1 ­ 4 will flash in unison at a rate controlled by Rate Pot 1. Channels 5 ­ 8 will flash in unison at a rate controlled by Rate Pot 2.
Mode 15 ­ Fireworks: Channels 1 through 7 will fade up and down in sequence. Then channel 8 will flash twice. Rate Pot 1 controls the rate of channel 1 ­ 7 and Rate Pot 2 controls the rate of the 2 flashes on channel 8.
Mode 16 ­ All On: All Channels on continuously.

( Power supply, LED's not included )

This unique board will allow use of a RC joystick or any wizard board servo output to control eight channels of remote DC lights (LED or incandescent) in 2 different sequences. Each channel is capable of driving up to 200 mA of lighting. An on-board LED for each channel indicates that the channel is active. Two on-board SS relays ­ one for each sequence - will also activate depending on which sequence is selected. A Mode Selection Switch will allow the user to toggle between Momentary On or Toggle On/Off modes. For example, with the Mode switched to Mode 1 (Momentary On), when the RC joystick is tilted to the left, Sequence 1 will start and Relay 1 will activate. Sequence 1 and Relay 1 will continue to be active as long as the joystick stays in the left position. When the joystick is in the center position, neither sequence will be selected. In Mode 2 (Toggle On/Off), when the joystick is tilted to the left and then returned to the center position, Sequence 1 will start and Relay 1 will activate. The sequence will continue and the relay will stay activated as long as the joystick remains in the center position. To stop this sequence, the user must tilt the joystick to the left a second time, toggling the sequence off. The same applies for Sequence 2. There are 2 potentiometers on board, one for each sequence that allows the user to control the rate of each sequence. The board has an on-board On/Off switch. Power to the board is supplied by the 5V line of the RC Servo connection and should have sufficient current to drive the board and all of the eight light channels (~2A max).

Sequence 1 ­ Cylon Effect:
When the Joystick is tilted to the left, Relay 1 actuates and a single channel rasters back and forth. Rate 1 Potentiometers will control the rate of the rastering.

Sequence 2 ­ Strobe:
When the Joystick is tilted to the right, Relay 2 actuates and all channels strobe on and off in unison. Rate 2 Potentiometer will control the rate of the channel strobing.


( Radio Control System, R/C Receiver, Power supply, LED's not included )

This programmable board setup allows user to control a Solid State dimmer used with AC Lighting. There is a 4-Line by 16 Character back-lit LCD that is the user interface for programming the different modes of operation. There are 8 modes of operation available to the user. These modes are set up and initiated using a menu-driven display with input being made by 4 on board pushbuttons.
The board requires 12 to 24V DC at least 100 mA power supply.
Programmable Recording time - 10 Minutes
Some of the user modes include ramp up/down lighting, full on, power up and hold and more.

Controller has remote trigger for remote activation,, on board potentiometer to set and program variable dimming outputs, Power On and Off switch, LED, sync port to trigger other boards connected. Wire terminal blocks, power jack for easy hook-up.
Large Wire Terminal Blocks for AC power, cord connections.

Dimmer Control can handle 15 Amp
(Power supply, AC power cord, Lighting not included)

click on image for a closeup view

Main CPU Board Size:
2-3/4" Long x 2-1/8" Wide x 1" High

LED (2) Board Size:
1-1/8" Long x 1/2" Wide x 3/8" High

Power Adapter Board Size:
1" Long x 7/8" Wide x 3/8" High

CDS Sensor Board Size:
7/8" Long x 1/2" Wide x 1-1/4" High

Power Supply
7-24 V DC @ 100 mAmp Power Supply ..

Board is pre-assembled and tested.

Application Example - Robot Head

Example Setup

This Microprocessor controlled board was designed to produce 15 different light effects via 2 Bi-Color LEDs. A shadow moving across a CDS cell will trigger the selected effect. Once triggered, the effect will last for a period of time determined by the Cycle Time Potentiometer which can be up to 30 seconds long. The rate at which the effect occurs (i.e., flashing, fading) is determined by the Rate Potentiometer. Every time an effect is triggered, a 80 mS pulse occurs at the Synch Output terminal block. This can be used to trigger another board. All connections to the board are through small daughter boards. The board requires a 7.5 to 24V DC, 100 mA power supply.

Mode 1: Two LED's will strobe RED when activated.
Mode 2: Two LED's will strobe GREEN when activated.
Mode 3: Two LED's will fade RED up and down.
Mode 4: Two LED's will fade GREEN up and down.
Mode 5: One LED will strobe GREEN and the other will strobe RED.
Mode 6: One LED will fade up and down GREEN and the other LED will fade up and down RED.
Mode 7: LEDs will alternate strobing RED
Mode 8: LEDs will alternate strobing GREEN.
Mode 9: LEDs will alternate strobing RED and then GREEN.
Mode 10: One LED will strobe RED while the other LED fades up and down GREEN.
Mode 11: LEDs will fade up RED and then stay on for one minute and then fade down.
Mode 12: Both LEDs will come on RED, stay on for the set Cycle Time, then flash 3 times, stay on for another Cycle Time and then go off.
Mode 13: Both LEDs will come on GREEN, stay on for the set Cycle Time, then flash 3 times, stay on for another Cycle Time and then go off.
Mode 14: LED's fade up RED, then fade to ORANGE, then to GREEN and then fades off.
Mode 15: One LED fades up RED, then fades to ORANGE, then to GREEN and then fades off while the other fades up GREEN, then fades to ORANGE, then to RED and then fades off.
Mode 16: In this mode, each time the board is triggered, it cycles through each of the 15 modes one at a time.


( Power Supply , Connection Wires not included )

Unique set of board will control 3-Channels of LED's Switched On and Off by remote activation. The three channels can be connected by ribbon cables to the LED Extension Boards for as long as needed.
Each Switch Bank will control one effects section, each effects section can operate 3 outputs (9 total outputs available)
Board has input connection for remote activation by relays, switches or controller board.
LED Status indicators for activated channels.
Quick power connector, Ribbon extension connector

LED Wire terminal blocks for quick connection
Board requires 9 Vdc @2 Amp Power supply

LED Extension board has ribbon connector, wire terminal blocks for LED wires and LED ststus lights for each of the 3 channels.

LED Strobe Control Board, will strobe 3 channels with user set rates and cycles

LED Fader Control Board, will fade up and down 3 channels with user set rates and cycles.



( Power Supply, LED's Wire Ribbon / Connectors, LED lighting fixtures not included )

Driver board will control two (2)12 VDC Light Bulbs or a string of LED's in an alternating (Back and Forth, like Rail Road Crossing Signal) Flashing effect

Board requires 12 VDC power supply
Output switching of board is 24 Watts (2 Amps) at 12 Vdc load
On board potentiometer to adjust alternating flash rate
Wire terminal block for 12VDC power connection
Wire terminal blocks for quick connection of LED/s or Light Bulbs

Board requires 12 Vdc @2 Amp Power supply

( Power supply, LED's / Light Bulbs not included )

Driver board will control three (3)12 VDC Light Bulbs or a string of LED's in a sequence action of 1, 2, 3 repeating over and over effect. Flash rate can be adjusted by on-board potentiometer

Board requires 12 VDC power supply
Output switching of board is 24 Watts (2 Amps) at 12 Vdc load
On board potentiometer to adjust alternating rate
Wire terminal block for 12VDC power connection
Wire terminal blocks for quick connection of LED/s or Light Bulbs

Board requires 12 Vdc @2 Amp Power supply

( Power supply, hookup wire, LED's / Light Bulbs, switch, enclosure box not included )

Board accepts audio input from any non-amplified sound source (computer, CD player, or Digital Sound Board) and activates a Solid State Relay ON and OFF in sync with the incoming audio signal. The on-board 1 Amp Solid State Relay can be connected to any device using (3-60 Vdc @ 1 Amp power). Common application include driving a pneumatic solenoid valve, water valve to sound or operating large bank of LED's -DC lighting to the incoming sound.

There is an on-board potentiometer that is used to adjust the sensitivity to the incoming sound. The board has a 1/8" phono jacks for input that can be switched as a left or right audio input signal for more precision audio sync to incoming sound signal track.

An on board LED indicates when the 1 Amp Solid State Relay is activated. Relay has wire terminal block contacts for connecting directly to device / load and quick connect power jack or wire terminal block for device power input.

Board can operate devices requiring 5-24 VDC at 1 Amp load.
Board uses two power inputs, one for the on-board electronics and another for the solenoid valve. (9-12 Board Power, 5-24Vdc Load Power)

Max Relay Output Current = 1 Amp
Relay Voltage Input 3-60 VDC

Two Power Load version available
Sound Activated SS Driver Board 9-12 VDC Version
Sound Activated SS Driver Board 9-24 VDC Heavy Duty Version

( Power Supply, Sound Source Audio Cable, Solenoid not included )