Board Size: 4-1/4" L x 2-7/8"
Wizard Board is pre-assembled and tested.
Controller has 7-bit Resolution.

Wizard - 1 Board Document

Application Note

Product Video

The Wizard - 1 Board is a small 9 Volt dc powered interface board that will record and playback up to 5 minutes of servo motion for 4 standard 5 Vdc hobby R/C type servos and control 4 digital switched ON and OFF outputs at +4.5 Vdc (100 mA) per channel.

The Wizard - 1 board incorporates many features such as looping playback servo motion with variable delay between loops. An auto start-up on power option and on board connector for remote activation switching such as a PIR sensor, contact switch or mat pressure pad to initiate playback.

Recording sessions are built up on a channel by channel process - no complex programming is required. During recording, all previously recorded channels are re-played to aid synchronization the current channel being programmed. Programming is easily done, with a set of push button keys and control potentiometer built onto the board.
No host computer or other programming device is needed to operate the board, Board has 7-bit Resolution.
Programmable Recording time - 5 Minutes

Power supply, Servos, not included.
( 9 Volt dc @ 2 Amp power supply needed )

Click on image for a larger view







Board Size: 6-5/8" L x 4-1/2" W
Wizard - 2 Board is pre-assembled and tested.
Controller has 7-bit Resolution.

Wizard - 2 Board Document

Wizard - 2 Board Applications -1

Note:
Regulated 9 Vdc @ 2 Amp and
Regulated 5 Vdc @ 2 Amp
power supplies recommended



Product Video

The Wizard - 2 Board will record / playback up to 5 minutes of action for up to 4 -R/C type servos and 4 - digital outputs or can be selected to operate 8 digital outputs with on board relays or direct digital signal output connection pads each with 5 minutes also per channel of recording time. The board also incorporates features such as looping playback action with variable delay between start-up on power up and sensor input. A terminal connection block for remote switch, pressure pad or synch signal from other device to initiate playback sequences is built on board also.

Recording sessions are built up on a track-by-track basis - no programming is required. During recording, all previously recorded tracks are re-played to aid synchronization.

FEATURES:

- 4 Servo output channels, each capable of recording and playback of up to 5 minutes of action.
- 8 Digital channels - 0/4V dc at 100 mA outputs each capable of recording and playback of up to 20 minutes of action
- 8 on board Relays ( 2 Amp @ 30 Vdc)
- Relay wire terminal connection blocks.
- 8 direct digital control signals with connection pads.
- Potentiometer to adjust the servo positions during recording or to determine the time delay between play loops during automatic loop play - adjustable between 0 and 65 seconds.
- NEXT, PLAY and RECORD buttons.
- Record enable / disable jumper
- AUTO-PLAY and LOOP-PLAY switches
- Status LED's , Board has 7-bit Resolution.
- Many more unique features.
- Programmable Recording time - 5 Minutes

Unit comes with user manual and assembled board.
( Servos and 9Vdc, 5Vdc, power supplies not included )

The Wizard - 3 Board will record and playback up to 13 minutes of action for up to 8 R/C type servos and 8 digital outputs

8 - Servo channels
8 - Digital outputs
Digital Outputs (100 mA @ 4.0 Vdc)
Two selectable 30V @ 2 Amp relays on-board.
On-board programming keys and servo controller potentiometer.
Programmable Recording time - 13 Minutes

Servo recording sessions are built up on a track-by-track basis - no computer programming is required. During recording, all previously recorded tracks are re-played to aid synchronization. Board has 7-bit Resolution.

( 9 Vdc @ 2 Amp and 5 Vdc @ 2 Amp power supplies recommended )

Regulated Power Supplies ( 5 and 9 Vdc ) and Servos, not included.

The Wizard- 4 Controller Board or Programmable
4 - Channel Relay module will record and playback up to 25 minutes of controlled ON and OFF action for1 - 4 Outputs Relays.

The board incorporates such features as looping playback, variable delay between programmed routines, auto loop, auto start-up on power up, a connection terminal for remote switch activation by manual switch, PIR sensor, pressure pad, etc, to activate playback.

Recording sessions are built up on a channel-by-channel basis - no complex programming needed, or connection to a host computer to program routines. Board has many other features including on-board programing and function selection switches, Sync output, EEPROM protection, direct digital output pins, optional user selected jumper relay activation or power down setting.
The relay contacts are rated at 30 Volt DC @ 2 Amps.
Quick wire terminal blocks are built on-board for each relay, with a common connector jumper option.
Programmable Recording time - 25 Minutes
Programming is stored in EEPROM
Board has 7-bit Resolution.
Board is powered by a 9 Volt regulated power supply connected to the on-board 2.1mm socket.

Supplied built and tested.
( Regulated 9 Volts dc power supply not included )

Super Animatronic Board

2- servos, 2- Relays, Digital Out, Sound Chip and Sound to Motion,
all on one controller board.


Enhanced Sound now with
4 minute sound chip on board

Board Size: 6"L x 4"W x 1"H

Controller has 7-bit Resolution.
Wizard - 5 Board is pre-assembled and tested.

Recommended 9 Vdc @ 2 Amp power supply

Wizard - 5 Board Document

Wizard - 5 Board Applications

Product Video

The Wizard - 5 Board will record and playback up to 5 minutes of action for up to 2 servos and 2 digital outputs (on-board relays). It also incorporates a 4-minute audio recording and playback sound chip with the ability to control one servo channel either from recorded moves or from an audio signal, direct or from on-board sound chip.
The card includes features such as looping action with variable delay between loops, auto start-up on power up and a connection interface for a PIR, remote switch or pressure pad to initiate playback.
Recording sessions are built up on a track-by-track basis- no complex programming is required and no computer is needed. During recording, all previously recorded tracks are re-played to aid synchronization.

Wizard - 5 Board Features
2- Digital channels- either 0/4V @ 10mA outputs or relay rated 30V @ 2A .
2- Servo channels ­ one channel may be automatically controlled from an audio signal either from the line input or from the on-board sound chip.
4 minute, high quality sound chip- digital recording selected from either from the line input (ie from a sound card and wav files) or from microphone input.
Potentiometer to adjust the servo position and the time delay between loops in loop-play.
Digital ON-OFF, NEXT, PLAY and RECORD buttons.
Record enable/disable jumper, EEprom protect jumper.
AUTO-PLAY and LOOP-PLAY switches.
Sync output for multi-board operation.
Programmable Recording time - 5 Minutes
Remote start option- for switches, sensors / PIRs, etc.
Maximum and minimum set points to the audio servo channel, and many more features.

Power supply, Servos, not included.
( 9 Volt dc @ 2 Amp power supply needed )

Board Size:
3-4/8" L x 1-3/4" W x 1/2" H
Board is pre-assembled and tested.

Wizard - 6 Document

Application Note

Product Video

The Wizard - 6 Controller is a Random and Pulse motion Servo Controller.

The controller board will operate two servo channels each with there own unique random servo motion outputs and one channel with variable speed and time pulse motion servo output.
The controller allows for setting the range of each servo's travel motion limits, along with adjustable servo speeds and random time rate features.

This controller is excellent for creating random moving eyes (Left / Right - Up / Down) and head motions, eyelid blinks or in other effects where automated random servo motion is needed using a self-contained servo motion driver board. No programming is required.
Board operates from a regulated 9 VDC @ 2 Amp power supply.

( Power supply, servos not included )

The Wizard - 7 is a 3- channel interface board that will operate a standard 12 Vdc motor in clockwise and counter clockwise rotation with speed control and activate 2 on - board relays when connected to a standard servo controller board or R/C receiver. This interface connects to any of the Wizard, Puppet boards or a R/C receiver and uses a servo output to operate in automated mode.

The on-board relays can be operated independently with latching on and off features or the two relays can be controlled together by moving an on-board jumper, allowing a single servo control channel to operate the relays as momentary on and off relays.

When this interface is connected to a Wizard, Puppet board the interface can be programmed for automated playback.

Vdc Motor driver is rated 12 Vdc @ 5 Amp continuous use.
Relays are rated at 30 Vdc @ 2 Amp load each.

( Vdc motor and power supply not included )
( Wizard board, R/C transmitter and receiver not included )

The Wizard - 8 board provides a single channel, user programmable 5 - minute digital output (relay) combined with a digital 4 - minute duration user record IC sound chip. The supplied 4 - minute ISD sound chip has great frequency response up to 3.4 KHz and a audio sample rate of 8.0 KHz. Audio can be re-recorded up to 100,000 times and can be stored up to 100 years.

One - Digital channel - either 0/4.5V @ 50mA output or on-board relay rated 30V @ 2A with wire terminal strip.
One - 4 minute quality digital IC sound chip.
Digital recording to Sound IC chip is through a direct line input (Computer sound card or output port, CD player or any sound source output).
Potentiometer to adjust the time delay between loops in playback of recorded sound and relay action ON and Off.
Digital ON - OFF and GO programming buttons, AUTO - PLAY, PLAY - RECORD and SOUND - RELAY switches. No computer is needed for programming.
Programmable Relay Recording time - 5 Minutes
Programmable Sound Recording time - 4 Minutes
Sync output for multi-board and link to other Wizard board operation
REMote start option - for interfacing to sensors, switches, remote relays, pressure pads, PIR sensors, etc.

Board operates from regulated 9 VDC @ 1.0 Amp power supply.
( Power supply, audio cable, remote audio amplifier and speakers not included.)

Board Size: 4" L x 3" W x 1/2"H
Mechanical relay rated 30V @ 2Amps

Controller requires 9 Vdc power.
Board is pre-assembled and tested.

Controller Instructions

The Wizard 9 board will record and playback up to 25 minutes of action for up to 2 digital / relay outputs. The board also incorporates features such as looping action with variable delay between loops, auto start-up on power up and a connection interface for a PIR, remote switch or pressure pad to initiate playback.

Specifications:

2 Digital channels- either 0/5V @ 100mA outputs or mechanical relay rated 30V @ 2Amps to wire terminal blocks,.
On board Potentiometer to determine the time delay between play loops during automatic loop play- adjustable between 0 and 65 seconds.
Digital 1, Digital 2 on-off, NEXT, PLAY and RECORD buttons.
Record enable/disable jumper protection.
Programmable Relay Recording time - 25 Minutes
AUTO-PLAY and LOOP-PLAY switches
Sync output for multi board operation
REMote start option- for interfacing to pressure pads / PIRs switches, relays, manual start buttons, etc.
REM polarity select jumper- start on either +5v or 0V condition.
Board operates from 9 Vdc power supply
( 9 Vdc Power Supply, not included.)

The top right-hand bank of input pins are the Digital sound-channels 1-8 audio playback select pins, also included the random and sequential play options as found on the sound 60 board

The other 8 banks of pin-sets along the back edge are for selecting which sound track goes to which output- jack matrix. ( remote amp and speaker )

Pin-set 1 (on the extreme left) relates to sound track 1- if you want sound track 1 to play-back through outputs 2, 6 and 8 you would put a jumper over pins 2, 6 and 8 on pin-set 1.

If you want to play sound -track 2 through outputs 1,3 and 5 then you would put jumpers over pins 1, 3 and 5 on pin-set 2 etc.
.................Application Example

Programmable board will switch 8 different digital recorded audio signals to 1-8 different output channels.

User can program board to switch 8 different audio signal to any of 1-8 output channels.
Any combination of audio out channels can be activated on and off.
Controller is easy to program and setup.
Board comes with 4 minute Audio chip on board, but can be switched to 8 or 12 minute chip upgrade option.

There is 1 audio jack input for recording 8 different sounds into the Digital sound chip directly by an audio source and 8 on board line output channels jacks to remote amps and speakers setups.

There is the standard record/playback mode jumper selection along with led indicators. Board can even be set to play random or sequence sound playback when triggered

You can adjust the play-back output select jumpers at any time- they are read just before starting any new play-back.

When the audio is combined with any of the Wizard Relay boards, the system becomes an automated audio sound effects and switcher system.

(Audio source, speakers and amps not included)
(9 Vdc Regulated Power supply not included)

(Wizard board, switches, wires, not included)

Ultimate Animatronic Board

6- Servos, 2- Relays, 4- minute Digital Out,
Sound Chip and Sound to Motion
(AutoTalk) control, all on one single controller board.

Click on image for larger view


Board Size:
7-3/8" L x 4-1/8" W x 1/2" H
Board is pre-assembled and tested.
Controller has 7-bit Resolution.

NOTE:
The Wizard -11 requires
duo power supplies

9 VDC @ 1.0 Amp power supply .....
5 - 6 VDC @ 2.0 Amp power supply
(Servo Power)

Wizard -11 Controller
-vs-
Other Controllers

YouTube Videos of Animatronic
Characters using Wizard Boards

The Wizard - 11 Board will record and playback up to 6 minutes of action for up to 6 servos and 2 digital outputs (on-board relays). It also incorporates a 4-minute audio recording and playback sound chip with the ability to control one servo channel (AutoTalk) either from recorded moves or from an audio signal, direct or from on-board sound chip.
The card includes features such as looping action with variable delay between loops, auto start-up on power up and a connection interface for a PIR, remote switch or pressure pad to initiate playback.
Recording sessions are built up on a track-by-track basis- no complex programming is required and no computer is needed. During recording, all previously recorded tracks are re-played to aid synchronization.

Wizard - 11 Board Features
2- Digital channels- either 0/4V @ 10mA outputs or relay rated 30V @ 2A .
6- Servo channels ­ one channel may be automatically controlled from an audio signal either from the line input or from the on-board sound chip.
4 minute, high quality sound chip- digital recording selected from either from the line input (ie from a sound card and wav files) or from microphone input.
Potentiometer to adjust the servo position and the time delay between loops in loop-play.
Digital ON-OFF, NEXT, PLAY and RECORD buttons.
Record enable/disable jumper, EEprom protect jumper.
AUTO-PLAY and LOOP-PLAY switches.
Programmable Servos, Relay Recording time - 6 Minutes
Programmable Sound Recording time - 4 Minutes
Sync output for multi-board operation.
Remote start option- for switches, sensors / PIRs, etc.
Maximum and minimum set points to the audio servo

NOTE: The Wizard -11 requires twin power supplies.
On board electronics operate from regulated 9 VDC @ 1.0 Amp power supply
On board Relays and servo outputs operate from regulated 5 - 6 VDC @ 2.0 Amp power supply

( Power supplies, audio cable, remote audio amplifier servos not included.)

Manual operated servo driver board will move a R/C servo in response to hand held remote slide or rotary position potentiometer input.

Specifications:
1 - channel manual servo control.
Servo output 1 to 2msec pulses.
Servo Travel A-B limits can be easily set.
Servo quick pin header connection.
Wire terminal block for remote potentiometer control.
Servo Travel 0 - 90 Degrees.
Quick Power connection
Operates from 7-12 Vdc @ 1 Amp power supply
Note: Controller board requires Potentiometer for operation.
( Board uses a 5 - 10K ohm potentiometer)
( Power Supply, not included.)
( Remote potentiometer not included )
( R/C servo not included )

Board Size: 167 x 86mm

Controller requires
12 Vdc at 2 Amp power Supply
Board is pre-assembled and tested.

Controller Instructions

The Wizard 13 board provides up to 6 minutes of recording and playback time for up to 6 digital outputs, 2 PWM and 4 DAC outputs.
The Wizard 13 incorporates looping play with variable delay between loops and Voltage outputs selectable between 0 - 5V and 0 -10V .

Specifications:
Connections
Power supply- 12V DC at up to 1 amp (current requirement depends on loads). 2.1mm socket, centre positive.
Outputs: Data is logged and updated during playback every 50msecs
Digital: Six buffered digital outputs, 0/5V DC at up to 100mA each. Connections via 2-way terminal blocks
PWM: Two channels of buffered PWM , 0/5V DC at up to 100mA each. PWM frequency is 15.6kHz with 8-bit resolution. Connection via 2-way terminal block.
DAC: Four channels of variable voltage at up to 25mA each. Range jumper to select either 0-5V or 0-10V Dc range both with 8-bit resolution
AUTO-PLAY and LOOP-PLAY switches
Sync output for multi board operation
REMote start option- for interfacing to pressure pads / PIRs switches, relays, manual start buttons, etc.
Board operates from 12 Vdc at 4 Amp power supply
( 12 Vdc Power Supply, not included.)

Board Size:135 x 85mm

Controller requires
6 Vdc at 4 Amp power Supply
Board is pre-assembled and tested.

Controller Instructions

The Wizard 14 allows the forward - reverse programmable control of up to 6 small 3-4.5V DC motors. The board incorporates loop play with variable time delay and auto play back at power up. Up to 6 minutes of motor action may be recorded. Actions are recorded in real time and a recording session built up on a channel by channel basis.

Specifications:
Motors Connections via 2-way terminal blocks for up to 6 small DC motors with current requirements of up to 250mA each.
Programmable on board Clockwise (CW) and Counter - Clockwise (CCW) motor control.
Record enable/disable jumper protection.
AUTO-PLAY and LOOP-PLAY switches
Sync output for multi board operation
REMote start option- for interfacing to pressure pads / PIRs switches, relays, manual start buttons, etc.
Board operates from 6 Vdc at 4 Amp power supply
( 6 Vdc Power Supply, not included.)

Board Size: 100 x 150mm

Controller requires
9 Vdc at 500mA power Supply
Board is pre-assembled and tested.

Controller Instructions

The Wizard 15 I/O router board provides a convenient way of matching up to 8 inputs with up to 8 outputs at 5V TTL levels. The board can accommodate normally high or low inputs and outputs and one single input may be routed to any or all of the output lines. A small led by each output indicates the current status.

Specifications:
Power Supply: 2.1mm connector, centre positive. 9V DC at 500mA
Inputs: 8 inputs via 2-way terminal blocks. The "-" connection is to the board ground. Each of the + connections is pulled to +5v by a 10k resistor.
Inputs may be volt-free or 5V TTL.
Outputs: 8 outputs via 2-way terminal blocks and a 2x8 pin header connector.
Each output is capable of sinking or sourcing up to 25mA.
On board wire header connections
Board operates from 9 Vdc power supply
( 9 Vdc Power Supply, not included.)

The AutoTalk -E2 board is similar in function with all the exact features of the original AutoTalk board developed several years ago for professional animatronic clients, in that it moves an R/C type servo in response to either an audio input signal from any standard CD player, tape recorder, sound source, but now has jumper setting for greater sensitivity in using the board from a sound source with low signal input, such as found on a digital sound chips or direct connected mic amplifier and dynamic microphone setup. The board has an on-board voltage regulator for using a variety of voltage sources including the use of a battery for remote applications, a quick connector for connecting power, LED power status indicator and enhanced output to operate a standard R/C servo with greater response. The controller includes the function to set both the servo end travel points, an important feature when working with various mouth jaw sizes, the servo arm direction of travel can also be quickly changed by an on-board jumper and the sensitivity of the audio input signal through the improved on-board gain control have also been enhanced for greater response.

( 9 Vdc Power supply, servos, sound source not include )

Note: When using a Dynamic Microphone that is not amplified, an optional Dynamic Microphone Amplifier is needed between the mic output and AutoTalk audio input.

The Programmable Single Relay Module has sufficient memory to record up to 4.5 hours of Relay ON/OFF programmed actions.

Programming is easily done on-board with a set of jumpers.
Playback can be initiated by remote switch, or set for repeat looping playback.
The relay contacts are rated at 24 Volt DC @ 0.5 Amps and have no relay closure sound when activating.
Programmable Relay Recording time - 4.5 Hours
Programming routine is stored in EEPROM.

The module draws only 4 mA and 15 mA with the relay energized.

The Programmable Single Relay Module is small
only 1-7/8" L x 1" W x 5/8" H ( 9 -Vdc battery size )

Uses a 9 Volt battery or 9 Volt dc AC wall adapter.

Supplied built and tested.
( 9 volt power supply not included )

Great for triggering sound boards, animatronics use.

The Programmable Single Relay - B Module is similar to the Relay - A module with memory to record up to 4.5 hours of Relay ON / OFF programmed actions, but has a bigger relay on-board to handle larger loads ( 24 Vdc @ 2 amp), power On / Off switch, status LED's and on-board solder pads for permanent wiring directly to board.

Programming is easily done on-board with a set of jumpers.
Playback can be initiated by remote switch, or set for repeat looping playback.
Programmable Relay Recording time - 4.5 Hours
Programming routine is stored in EEPROM.

Uses a 9 Volt battery or 9 Volt dc AC wall adapter.

Supplied built and tested.
( 9 volt power supply not included )

Great for the Animatronics and Haunted Industry.
Very versatile relay board.

The ANIMATE BOARD is a 9 Volt dc powered full feature Sound, Motion and Switched ON / OFF output control interface board.

The controller has on-board sound recording and playback in to a 20 second sound chip with microphone and speaker output and up to 40 seconds of recorded and playback motion saved to a EEPROM for 4 standard +5 Vdc servos and control of 4 digital switched ON and OFF outputs at + 4.5 Vdc (100 mA) per channel action.

The Animate board incorporates many features such as looping playback servo motion with variable delay between loops. An auto start-up on power option and on board connector for remote activation switching such as a PIR sensor, contact switch or mat pressure pad to initiate servo playback and on- board sound output.

Recording sessions are built up on a channel by channel process - no complex programming is required.
During recording, all previously recorded channels are re-played to aid synchronization the current channel being programmed.Programming is easily done, with a set of push button keys and control potentiometer built onto the board.Speaker connection terminal allow the addition of an 8-16 ohm speaker which can be driven directly from the Animate board .Motion, Sound and Switched ON / OFF outputs are all controlled from a single board.Connection pins on-board for servos, output hookups.

Programmable Servo Recording time - 40 Seconds
Programmable Sound Recording time - 20 Seconds
( 9 Volt dc - 2 Amp Power Supply, Servos and Speaker not included ).......

Small controller for single servo control with up to 4 minutes recording time, loop playback with variable time delay between loops, auto start-up and easy recording features. Several modules may be daisy chained together and controlled from one master module.

The Puppet servo controller includes the following features:

- Single channel servo control
- Up to 4 minutes recording time
- Small modification to board, allows a servo to be
controlled by a hand push button switch, great for
Costume Animatronic Head control.
- Programmable Servo Recording time - 4 Minutes
- Full 180 degree rotation pulse train (for servos that can physically rotate 180 deg)
- Looping play with adjustable time delay between loops Record edit function
- Synchronization pulse for multiple unit operation

( 5 Volt dc power supply and Servo not included )

Small controller for single servo control with up to 4 minutes recording time, loop playback with variable time delay between loops, auto start-up and easy recording features. Several modules may be daisy chained together and controlled from one master module.

The Puppet Controller has an additional digital channel with a 1A @ 24 Vdc rated relay.
Record your servo channel first and then superimpose the digital channel whilst the servo is playing
The Puppet servo controller includes the following features:
- Single channel servo control
- Programmable Servo , Relay Recording time - 4 Minutes
- Full 180 degree rotation pulse train (for servos that can physically rotate 180 degrees)
- Looping play with adjustable time delay between loops Record edit function
- Synchronization pulse for multiple unit operation

( 5 Volt dc power supply and Servo not included )

.YouTube Videos of Animatronic
Characters using Puppet Controller

The Joystick Servo Controller is a dual channel servo controller capable of direct manual servo, relay control and with recording option of up to 13 minutes of servo and relay action, interfaced to a standard game joystick.

The board features loop playing with variable delay, synchronized playback, can be linked with several other boards for multiple servo applications, has servo movement limit setting and a single relay channel output.

Joystick forward and backwards controls servo one motions.
Joystick left and right controls servo two motions.
Thumb button = playback / recording
Trigger button = relay ON/Off control.

Pressing down and holding the Thumb button will activate the record option where joystick / servo motion is recorded to an on-board EEPROM for playback up to 13 minutes.
Playback motion can be later activate by pressing the finger button, anytime, even between manually servo control.
Board power is provided by plug-in wall unit, or optional mobile power supply and will operate both joysticks and servos.
Programmable Servo, Relay Recording time - 13 Minutes.

NOTE: Analog Joystick with DB-15 connector required. Will not work with new USB type joysticks.
( 9 Volt dc Power supply, Servos and Joystick not included )

Joystick Adapter Kits- Build Your Own Joystick Interface
( Joystick, power supply, servos, not included )

Joystick Controller Document

Joystick Controller Applications

Product Video

Control board for manual operation of a single R/C type servo by remote switch, relay, wireless control or external automated controller signal pulse.
( Servo travel positions A to B or B to A, under switch signal operation ) When remote manual switch is activated servo arm will move to pre-programmed position (Min / Max) and return back to start pre-programmed position when remote switch is de-activated If remote switch is held active servo arm will stay in position until switch is de-activated.
Board also has on board Solid State Relay that can be manual operated On and Off with remote switch, external relay pulse, wireless controller.

Controller includes the following features:
- Single channel servo control.
- On-board connection for remote switch or relay.
- On-board Servo and Power Connection terminals.
- On-board travel adjustment for Servo Movement.
( A through B Min and Max positions )
- On board servo reversal switch
- Program buttons allow servo arm to be positioned with Start and Stop at any position between A and B travel and recorded to memory for playback.
- Servo Travel Position A to B - B to A control.
- Solid State Relay rated at 2amp switching (Com, NO.terminal contacts)
- 7-12 Vdc operation - Wall power or Mobile Battery
- Wire terminal blocks, Status LED's power connector, servo header pins.

(Power supply, hand switch button unit and servo not included )

Hand / Palm switch units can be custom designed to fit your unique needs. Call Blue Point Engineering for more information on a custom design.

This board uses a positive 0-10 Vdc signal to control the position of a servo
The PIC microprocessor servo controller board provides a single channel capability of converting a positive 0 -10 Vdc adjustable control voltage input into a output suitable for driving a standard hobby R/C servo travel positions in relation to the voltage input. Voltage range 0 - 10 is directly related to servo positions
Servo travel position limits (min, max) can be pre-programmed into memory for playback.
Board can also be used to translate 0-10 dc voltage to PWM signals 1.0 to 2.0 msec
(0 Vdc =1.0 msec PWM)
(5 Vdc =1.5 msec PWM)
(10 Vdc =2.0 msec PWM)
(Various Vdc 0-10 levels provide PWM signals between 1.0 msec to 2.0 msec)

Specifications:
Servo connection pin header for quick connection.
1 - Channel Analog 0 -10 Vdc DC input.
VDC terminal block for wire connection.
Power jack for quick connection of 5 Vdc supply.
Servo output 1 to 2msec pulses.
Servo Travel 0 - 90 Degrees.
On-Board servo travel (min, max) position programming buttons.
Servo position reverse A-B, B-A travel switch on controller board.
Status LED lights
On/Off Power Switch with LED light

( power supply not included )
( Variable 0 -10 Vdc supply not included )
( R/C servo not included )