Board Size: 4-1/4" L x 2-7/8"
Wizard Board is pre-assembled and tested.
Controller has 7-bit Resolution.

Wizard - 1 Board Document

Application Note

Wizard-1 Manual

The Wizard - 1 Board is a small 9 Volt dc powered interface board that will record and playback up to 5 minutes of servo motion for 4 standard 5 Vdc hobby R/C type servos and control 4 digital switched ON and OFF outputs at +4.5 Vdc (100 mA) per channel.

The Wizard - 1 board incorporates many features such as looping playback servo motion with variable delay between loops. An auto start-up on power option and on board connector for remote activation switching such as a PIR sensor, contact switch or mat pressure pad to initiate playback.

Recording sessions are built up on a channel by channel process - no complex programming is required. During recording, all previously recorded channels are re-played to aid synchronization the current channel being programmed. Programming is easily done, with a set of push button keys and control potentiometer built onto the board.
No host computer or other programming device is needed to operate the board, Board has 7-bit Resolution.
Programmable Recording time - 5 Minutes

Power supply, Servos, not included.
( 9 Volt dc @ 2 Amp power supply needed )

Board Size:
3-4/8" L x 1-3/4" W x 1/2" H
Board is pre-assembled and tested.

Wizard-6 Manual

Wizard - 6 Applications

Product Video

The Wizard - 6 Controller is a Random and Pulse motion Servo Controller.

The controller board will operate two servo channels each with there own unique random servo motion outputs and one channel with variable speed and time pulse motion servo output.
The controller allows for setting the range of each servo's travel motion limits, along with adjustable servo speeds and random time rate features.

This controller is excellent for creating random moving eyes (Left / Right - Up / Down) and head motions, eyelid blinks or in other effects where automated random servo motion is needed using a self-contained servo motion driver board. No programming is required.
Board operates from a regulated 9 VDC @ 2 Amp power supply.

( Power supply, servos not included )

Manual operated servo driver board will move a R/C servo in response to hand held remote slide or rotary position potentiometer input.

Specifications:
1 - channel manual servo control.
Servo output 1 to 2msec pulses.
Servo Travel A-B limits can be easily set.
Servo quick pin header connection.
Wire terminal block for remote potentiometer or switch control.
Standard Servo Travel 0 - 180 Degrees.
Quick Power connection
Operates from 7-9 Vdc @ 1 Amp power supply
Note: Controller board requires Potentiometer or switch for operation.

( Board uses a 5 - 10K ohm potentiometer)
( Power Supply, not included.)
( Remote potentiometer, switch not included )
( R/C servo not included )

Small controller for single servo control with up to 4 minutes recording time, loop playback with variable time delay between loops, auto start-up and easy recording features. Several modules may be daisy chained together and controlled from one master module.

The Puppet servo controller includes the following features:

- Single channel servo control
- Up to 4 minutes recording time
- Small modification to board, allows a servo to be
controlled by a hand push button switch, great for
Costume Animatronic Head control.
- Programmable Servo Recording time - 4 Minutes
- Full 180 degree rotation pulse train (for servos that can physically rotate 180 deg)
- Looping play with adjustable time delay between loops Record edit function
- Synchronization pulse for multiple unit operation

( 5 Volt dc power supply and Servo not included )

This board uses a positive 0-10 Vdc signal to control the position of a servo
The PIC microprocessor servo controller board provides a single channel capability of converting a positive 0 -10 Vdc adjustable control voltage input into a output suitable for driving a standard hobby R/C servo travel positions in relation to the voltage input. Voltage range 0 - 10 is directly related to servo positions
Servo travel position limits (min, max) can be pre-programmed into memory for playback.
Board can also be used to translate 0-10 dc voltage to PWM signals 1.0 to 2.0 msec
(0 Vdc =1.0 msec PWM)
(5 Vdc =1.5 msec PWM)
(10 Vdc =2.0 msec PWM)
(Various Vdc 0-10 levels provide PWM signals between 1.0 msec to 2.0 msec)

Specifications:
Servo connection pin header for quick connection.
1 - Channel Analog 0 -10 Vdc DC input.
VDC terminal block for wire connection.
Power jack for quick connection of 5 Vdc supply.
Servo output 1 to 2msec pulses.
Servo Travel 0 - 90 Degrees.
On-Board servo travel (min, max) position programming buttons.
Servo position reverse A-B, B-A travel switch on controller board.
Status LED lights
On/Off Power Switch with LED light

( power supply not included )
( Variable 0 -10 Vdc supply not included )
( R/C servo not included )

Main Controller Board Size:
4-1/2" L x 4-1/28" x 1" H

Remote Potentiometer Board Size:
3-1/2" L x 1-3/8" x 1/2" H

Remote Switch Board Size:
4-3/4" L x 1-3/4" x 1/2" H

(9VDC) for the controller is required
(5VDC) for the servos is required

Application and Connection Setup Overview

This unique board set was designed to allow the use of either switches and/or potentiometers to manually remote control 4-servo motors and 1-Remote Solid State 2 Amp Relay. The switches or potentiometers are located on small remote boards that are connected to the main board via an 8 foot ribbon cable.
The minimum and maximum limits of movement for each servo can be programmed and are stored in non-volatile memory. There is also a Solid State relay that is activated by a toggle switch (also on the remote boards). The master control board has separate power entries for board power and servo power with the ability of using a remote switch to turn either on or off. Both remote switch and potentiometer boards have LED indicators that show the presence of board power and servo power.

Boards can be stacked to create an expanding servo control setup ( Two boards= 8 servo control, Three boards = 12 servo control, Four boards stacked = 16, ect ).
Control Boards can also be stacked to have one master board operated by switches another master board operated by potentiometers stacked together as one set. This unique design allows for easy development of a WALDO or puppeteer type interface setup.
Master control board requires Switch or Potentiometer board.
Separate power (9VDC) for the controller and a separate power (5VDC) for the servos is required

(Power Supplies, Potentiometer Board, Remote Switch Board, Servos not included )

Small control board allows independent manual control of any positions between A-B / B-A for two standard R/C servos by remote connected switches.

Controller includes the following features:
- Dual channel servo control.
- Independent channel Switch Control.
- On-board connection for remote switches (2)
- Full 180 degree rotation pulse (for servos that can physically rotate 180 degrees)
- 5Vdc operation - Wall power or Mobile battery
- Controllable servo travel Position A-B and B-A
- Servo Position can be stopped and held at any positions between A-B or B-A
- Small PCB Board
- On board power regulator, allowing controller board to operate from any 6-24 Vdc power supply.

( 9 Volt dc Power Supply, Switches, Servos not included )

Switch units can be custom designed to fit your unique needs. Call Blue Point Engineering for more information on a custom controller.

This small board will be found invaluable for projects and models using R/C type servos.

Test and calibrate hobbyist "R/C - Radio Control" type servos.
- Manual and Automatic Modes
- Variable speed 90 degree sweep facility
- Stand alone servo sweep function for animations
- 0 and 90 degree calibration LED Light (1ms and 2ms pulse widths check)
- Calibration LED light every 15 degrees

In Automatic mode, Servo-Check produces a pulse stream that makes the servo traverse smoothly through 90 degree at a speed determined by the potentiometer setting (approx 0.5 to 5 secs / 90 degree ).

Advanced users can add 2 standard 10k linear potentiometers to adjust the end stops for a simple, stand-alone animatronic controller module.

In Manual mode, the servo position is fully adjustable from 0 to 90 degrees by using the thumbwheel. Manual mode generates a standard servo pulse stream. The width of the pulses varies between 1.0msecs and 2.0 msecs depending on the position of the potentiometer. Turning the potentiometer fully to either end of its travel will cause the LED to light indicating that either a 1.0 or 2.0 pulse width which should correspond with a servo angle of either 0 or 90 degrees. Additionally, as the potentiometer is turned, the LED will light at positions corresponding to15, 30, 45, 60 degrees and 75 degrees , thereby providing a field calibration setup.

Works from standard 5-6 VDC supply and includes 3-pin header for all standard servos.

Supplied built and tested, ready for immediate use.
( 5 Volt Power supply and Servo not included )

Control Board will record and playback up to 5 minutes of servo motion for 3 standard 5 Vdc hobby R/C type servos.

The board incorporates many features such as looping playback servo motion with variable delay between loops. An on board connector for remote activation switching such as a PIR sensor, contact switch or mat pressure pad to initiate playback.

Recording sessions are built up on a channel by channel process - no complex programming is required. During recording, all previously recorded channels are re-played to aid synchronization the current channel being programmed. Programming is easily done, with a set of push button keys and control potentiometer built onto the board.
No host computer or other programming device is needed to operate the board,

Duo Power supplies, Servos, not included.
( 9 Volt dc @ 800mA power supply needed )
( 5 Volt dc @ 2 Amp power supply needed )

Specifications:
3- Servo channels ­ Operate R/C servos
Potentiometer to adjust the servo positions.
Potentiometer to adjust the time delay between loops in loop-play.
Programmable Recording time - 5 Minutes
Programming Buttons SERVO 1,2,3, PLAY buttons.
Record enable/disable jumper, EEprom protection switch
Remote start option- for switches, sensors / PIRs, etc
Many more features.

This unique board controls the movement of 4- R/C servos when applying a 12Vdc signal to the servo channel input selected. User can set the max and min servo travel position, so then when 12 Vdc is applied the servo will move directly to the max position programmed and hold as long as a 12 Vdc signal is active. As soon as the 12 Vdc signal is turned off, the servo will move to the min position programmed by the user

( Power supply, servos not included )

Board Size:
4-3/4" L x 5-1/4" W x 1" H
Application Setup Overview

This unique board controls the movement of 6 servos as random adjustable, with min and max servo settings set by the user.

The Controller uses 1 master microprocessor and 6 servo microprocessors to operate from. This board is excellent, wherever automated random servo movements are needed.

Controller has remote trigger for remote activation, on board LCD, buttons to set and program variables, Power On and Off switch with LED On indicator, Wire terminal blocks, power jack for easy hook-up. Servo connection header pins, and terminal blocks.

Board requires one 6Vdc @ 6 Amp power supply (Servo's) and one 9-12Vdc power supply for the on board electronics.

(Servo, Power Supplies not included)

Board Size:
4-3/4" L x 4-1/4" x 1" H

This unique board will allow the control of 4 servos manually via remote 10K potentiometers or by Wizard -1 Board control. The input (pots or Wizard Board) is selected by on-board slide switch or dry contact closure to the Remote Input Selection terminal block. When switched to (M)anual, the 4 servos are independently controlled by the remotely mounted pots. Minimum and maximum limits can be set for each servo but these limits are only in effect when the board is in (M)anual control. When in (W)izard mode, the Wizard Board will handle limits for the servos. There is an on-board SS relay that can either be activated by dry contact closure at the Remote Relay Trigger terminal block or by pressing the small pushbutton located next to the relay.

( Power supply, 10K potentiometers, Servos, Wizard -1 Board not included )

This unique BPE exclusive small custom controller board was designed to operate a standard R/C servo in several user modes. Mode one is running the servo to a programmed minimum and maximum limit by the push of button 1 or 2. The user can activate button 3 to play back a previously recorded user sequence of servo movement (up to 15 minutes recorded time).

Three Buttons on the control board or remote buttons determine what the servo will do ­ (1) move to the minimum position, (2) move to the maximum position or to (3) continuously loop the user recorded sequence. On board potentiometer / program button and EEPROM allow user to record and store servo routine needed (15 minutes )

The servo is connected to the board either by the 3-pin servo connector or by the servo terminal block. The board requires a power source 7.5V dc to 9V dc at 800 mA or greater. Power can be hooked to the board either by a 2.1mm power connector or by the alternate power terminal wire block.

Example Application 1: " Moving Wings "
Servo Position 1 ( Switch-1 ) Fairy Wings Closed
Servo Position 2 ( Switch-2 ) Wings Fully Open
Servo Position 3 ( Switch-3 ) Wings moving back and forth in motion routine programmed by user.

Example Application 2: " Monster Jaw Mandible "
Servo Position 1 ( Switch-1 ) Mandible Closed
Servo Position 2 ( Switch-2 ) Mandible Fully Open
Servo Position 3 ( Switch-3 ) Mandible moving back and forth in an attack or eating effect.

Board can operate by battery power or standard wall power supply adapter

(7-12 Volt dc power supply, battery, switches, Servo and wing mechanical mechanism not included )

This unique board was designed to allow the directional control of a DC motor by using a R/C servo output channel (PWM Signal).

Two modes of operation are provided and are selected by the on board Mode Switch. Toggle On and Off and Latching On and Off Control

The board is powered by the servo connection, but separate power must be provided for the DC motor.
There are 2 on-board 10A mechanical relays that work in conjunction to reverse the polarity of the power being supplied to the DC motor that is attached at the Motor Connection Terminal block.

The board takes standard servo input and when the input signal is signaling for full CW servo movement, Relay 1 activates, providing DC power to the motor. When the servo input is signaling for full CCW servo movement, Relay 1 deactivates and Relay 2 activates, reversing the polarity of the DC power to the motor.

( Motors , Power supply - Not included )

This unique BPE exclusive controller uses a pre-programmed PIC Microprocessor to manually drive up to 4 model / hobby R/C servo motors simultaneously from 2 on board mini joysticks. On-board mini joysticks move the corresponding servo motor over their full travel range when moved. Controller also has on-board Solid State Relay controlled by micro push button switch. Small board design, entire board fits into the palm of your hand!

Solid State State Relay rated 30Vdc @ 2 Amp.
3- Pin Headers for quick servo connection.
Quick power connector on-board. Center positive 2.5mm jack.
On-board Mini Joysticks - 2 axis control per unit.
Each mini joystick controls 2 servos. ( 4 servos - 2 joysticks ).
Master power On and Off switch and status LED.
Relay On and Off status LED and quick connection wire terminal block with SS Relay - COM and NO connections.
Small Board size : 3-7/8" L x 2-1/2" W x 1" H.

Requires 5 Volt dc @ 2 Amp power supply.
Servo motors , Power supply - Not included.

This unique board was designed to allow the remote operation of a Pan and Tilt camera system and has the ability to activate a cam recorder via an on-board SS relay.
The limits of servo movement is set and stored in non-volatile memory (servo Min and Max travel positions).
The servos can be moved independently or placed in Pan Mode where the Pan servo sweeps back and forth between the previously stored limits. While in the Pan Mode, the speed of movement left and right can also be adjusted by switch control

On-board mini tactile pushbuttons are on the board to allow the testing of all operations. Remote switches can be connected to on-board wire terminal blocks

Separate power (9VDC) for the controller and a separate power (5VDC) for the servos is required


( Power Supplies, Servos, Camera, Camera Bracket. Pan & Tilt , Control Switches not included )

Remote Board Size:
3-3/4" L x 1-7/8" x 1/2" H

Main Board Size:
4-3/8" L x 3-1/2" x 1" H

(9VDC) for the controller is required
(5VDC) for the servos is required

Application and Connection Setup Overview

This unique board was designed to allow the remote operation, by Manual, Relay or RF Relay Signal, 2 servo channels and 1 Solid State Relay connected to a Pan and Tilt camera system. The user will be able to control the camera positions and have the ability to activate a remote recorder via an on-board 2 amp SS relay.

The limits of servo movement is set and stored in non-volatile memory. (servo Min and Max travel positions) The servos can be moved independently or placed in Pan Mode where the Pan servo sweeps back and forth between the previously stored limits. While in the Pan Mode, the speed of movement can also be remotely adjusted.

On-board mini tactile pushbuttons are on the board to allow the testing of all operations.

The Remote Terminal Board allows it to be placed remotely from the Main Board. It is connected to the Main Board via a 4 foot ribbon cable. Switches, Relays, RF Control Relays can be connected

Separate power (9VDC) for the controller and a separate power (5VDC) for the servos is required

( Power Supplies, Servos, Camera, Camera Brackets, Pan & Tilt, Manual / Remote Switches, RF Relays, Remote Relays not included )

This unique controller board was designed to allow the use of 2 on-board joysticks to control 4 servo motors. The minimum and maximum limits of movement for each servo can be programmed and are stored in non-volatile memory.

There is also a SS relay that is activated by a toggle switch.
Relay rated at 2 Amps

The board has separate power entries for board power and servo power with the ability of using a remote switch to turn either on or off.


Board Requires 9 Volt dc @ 1 Amp power supply.
Board Requires 5 Volt dc @ 5 Amp power supply.

( Servo motors , Power supply - Not included )

This unique 4 channel servo and 1 channel solid state relay board was designed to allow the use of a remote joysticks in manual or in user program mode to control 4 servo motors and 1- solid state relay.

The joysticks are located on a small remote board connected to the main board via an 6 foot ribbon cable. The minimum and maximum limits of movement travel for each servo can be programmed and are stored in non-volatile memory.

There is also a Solid State relay that is activated by a toggle switch (also on the remote board). The board has separate power entries for board power and servo power with the ability of using a remote switch to turn either on or off. Both remote boards have LED indicators that show the presence of board power and servo power.

The user has the ability to record and playback up to 10.5 minutes of servo and relay activity. User can switch between manual and recorded playback with on board pushbutton switches. When user is in playback mode, and needs to manual control servos, a simple press of the red stop button , halts the playback routine and instantly allow control of the servos / relay by manual method. Programming servo / relay motion is set by on board selection switch and the activation of the red record/ stop button switch during real time programming.

Board Requires 9 Volt dc @ 1 Amp power supply.
Board Requires 5 Volt dc @ 5 Amp power supply.

( Servo motors , Power supply - Not included )