Tiny switch with connector header and 6" wire.
Connector attaches to any of the 2 Pin headers used on the Wizard, Puppet and Programmable Relays boards. Makes a great add-on device when programming,when you can't operate the programming jumper blocks or when the board is tucked away into a confined space where reaching the board is limited.


Examples of switch use.
( 1 ) Puppet Board
( 2 ) Programmable Relay Board

Tiny switch with connector headers and 2- 6" wires.
Connectors attache to the 2 Pin headers used on the Programmable Relays board. Makes a great add-on device when programming,when you can't operate the programming jumper blocks quickly enough or when the board is tucked away into a confined space where reaching the board is limited.

Examples of switch use.
( 1 ) Programmable Relay Board

Small board that quickly attaches to any of the Wizard or Puppet board Digital Outputs ports. Board has built-in LED's for channel output status and quick connector header blocks with 6" wire leads for connecting to the 2 pin headers found on the controller board digital outputs. Great for visual status as ON and OFF when programming the digital output ports, or for visual verification when operating other devices remotely connected to the digital output ports.

Small board with on-board 2.1 mm power jack, and quick connector header blocks with 6" wire leads for easy connecting remote battery or wall adapted power bricks to the 2 pin power headers found on the Puppet and Wizard boards.

Lead wire is color coded with Black and Red to aid in connecting proper power polarity to controller boards.

Available with or without small power jack pcb board.

Board Size: 7/8" L x 5/8" W x 1/2" H

Examples of use.
( 1 ) Wizard-I Board
( 2 ) Puppet Board

These modules are designed to assist in the quick connection of Pneumatic Valves, LED Light Strips, LED Bulbs or wherever there is a need for 12 Vdc power controlled through remote relays to a device.

Each module has a quick connect power jack, with on and off switch and LED power status.

A set of quick terminal wire blocks, makes hook-up to a device and connection to remote control relays easy to do.

Boards are labeled with input and output channels for quick identification and set-up.

Board Setup:
Input side has connections from remote relay outputs (Relay board not included)
Output side has connections for devices (LEDs, Valves,)
Quick Connector or wire terminal for 12 VDC power supply to feed power to the output side of board when remote relays are switched on.

Modules are rated for 5 Amps loads at 12 Vdc.

12 Vdc power supply not included.
Remote relays and controller not included.


....Example use of power modules

This module is designed to assist in the quick connection of a servo controller to servos that need power from their own power supply.

Module allows each servo to be controlled independently from the standard control signal (PWM) with power coming from a separate supply to operate servos with higher power needs or when the controller can not pass the needed power to the servos directly.

Module has a quick connect power jack, with On and Off switch and LED power status.

Wire 3-pin header blocks, make hook-up to servos and connection to servo controller easy to do.

Board is labeled with input and output channels for quick identification and set-up.

Module is rated for 5 Amps loads at 5-12 Vdc.

Power supply not included.
Servos and servo controller not included.

Small board designed to select by a remote manual switch two different servo inputs R/C controls to one servo output. Board also has a servo input headers and wire terminal block for remote selection switch.

Power, Ground common to all 3 servos. Servo Signals switched by remote 3 position switch

Remote Switch , Servos, Not Included

This module is designed to assist in the quick connection of a servo controller to servos that need power from their own power supply.

Module allows each servo to be controlled independently from the standard control signal (PWM) with power coming from a separate supply to operate servos with higher power needs or when the controller can not pass the needed power to the servos directly.

Module has a quick connect power jack, with On and Off switch and LED power status.

Wire 3-pin header blocks and micro terminal wire blocks make hook-up to servos and connection to servo controller easy to do.

Board is labeled with input and output channels for quick identification and set-up.

Module is rated for 5 Amps loads at 5-12 Vdc.

Power supply not included.
Servos and servo controller not included.

This module is designed to switch a single R/C controller to two different set of servos or can be setup to switch two different servo controllers to a single set of servos. Board also has a single input switch to two switched outputs

Module allows each servo to be controlled independently from the standard control signal (PWM) but can be switched to control a different servo set or controller set.

Wire 3-pin header blocks, make hook-up to servos and connection to servo controller easy to do.

Board is labeled with input and output channels for quick identification and set-up.

Servos and servo controller not included.

These modules are designed to assist in the quick connection of Pneumatic Valves, LED Light Strips, LED Bulbs or wherever there is a need for Vdc power control to various distribution points.

Each module has a quick connect power jack, with on and off switch and LED power status.

A set of quick terminal wire blocks, makes hook-up to a device and connection to remote control relays easy to do.

Boards are labeled with input and output channels for quick identification and set-up.

Modules are rated for 5 Amps loads at 12 Vdc.

12 Vdc power supply not included.

Small board that quickly attaches to any of the Wizard or Puppet board Digital Outputs ports. Board has four built-in LED's for channel output status and quick connector header blocks with 6" wire leads for connecting to the 2 pin headers found on the controller board digital outputs. Solder pads allow for other devices to be quickly wired to the Digital ports when experimenting with other devices to be controlled.

EEPROM Master Copy will duplicate the data stored in the EEproms used in the Puppet Board, Animate Controller Board and Wizard Controller Boards.

Very simple to use- load the recorded EEprom into the master socket, load a blank EEprom into the slave socket and press Go.

Instruction guide, assembled card ready to use.

( 9 Volt dc Battery not included )

....EEPROM Copier Document

Quickly connect switches, relays, etc to the Sound Board Pro channel 1- 6 control terminal block

Wire Terminal for quick Switches, Relays, etc connection.
Channel 1-6 connection
Ribbon Wire ( 4") and Connectors
Quick connectors on ribbon wire ends
Jumper for Looping Playback

( Sound Board Pro not included )

Solder Pads for Switches, Relays, etc.
Channel 1-6 connection
Ribbon Wire ( 4") and Connectors
Quick connectors on ribbon wire ends
Jumper for Looping Playback

( Sound Board Pro not included with Connectors )

Wire Terminal Connnector / Cable
Board Size Aprox:
1-1/2" L x 1-1/4" W x 1/2" H

Solder Pad Connector / Cable
( Image Not Shown )
Board Size: Aprox:
1-1/2" L x 1-1/4" W x 1/2" H

Click on Image for Close-up View

Switching / Effects Connector / Cable
Board Size Aprox:
1-3/4" L x 3/4" W x 1/2" H

Click on Image for Close-up View

Quickly connect switches, relays, etc to the Sound Board channel 1 - 8 control terminal block

Wire Terminal for quick Switches, Relays, etc connection.
Channel 1-8 connection, Common Connection
Ribbon Wire ( 4") and Connectors
Quick connectors on ribbon wire ends
Jumper for Looping Playback

Solder Pads for Switches, Relays, etc to Sound Board
Channel 1 - 8 connection, and common connection pads
Ribbon Wire ( 4") and Connectors
Quick connectors on ribbon wire ends
Jumper for Looping Playback


........... Example of adapter to Sound Board

Solder Pads and Wire Terminal block for a single switch Relays, etc to Sound Board - VEGAS
Channel 1 connection, and common connection pads
Ribbon Wire ( 4") and Connectors
Quick connectors on ribbon wire ends
Jumper for Looping Playback
Jumper for Sequential Playback
Jumper for Random Playback

( Sound Board - VEGAS not included with Connectors )

........... Example of adapter to Sound Board

Manual Mini Switches ( Channel 1 - 6 )
Ribbon Wire ( 4") and Quick Connectors
( Sound Board Pro to Adapter with quick connectors on two ends )
Back Side - Wire Terminals for Remote Switch Connection.
Jumper for Looping Playback.
Board Size Aprox: 3-3/4" L x 1-7/8" W x 3/4" H

( Sound Board Pro not included )

Board with Wire Terminals ( Channel 1 - 6 )
Mode - Wire Terminals ( Record / Playback Jumper)
Wire Terminals ( Power Switch, Power Connection to Sound Board Pro Module)
Jumper for Looping Playback
Ribbon Wire & Connectors ( Sound Board Pro to Adapter with quick connectors on ends )
Back Side - Wire Terminals for Connections.
Board Size Aprox: 3-3/4" L x 1-3/4" W x 7/8" H

( Sound Board Pro not included )

3 - Position Switch
|On-Off-On Momentary
Click on image for a close up view

2 - Position Switch
Off-On Momentary
Click on image for a close up view

Unique Switches used to control the Wizard-12 Control Board by manual control

3 - Position Switch - Servo travel B- A - C positions
Switch configured as On - Off - On
Servo movement Left, Center, Right

2 - Position Switch - Servo travel A-B / B- A positions
Switch configured as On - Off
Servo movement Left, Center

Switches come in 2 combination types
Switch mounted on PCB board
Switch remote - not mounted on PCB board.

PCB boards have wire terminal blocks for quick easy connections with on board resistor for correct servo control

Unique Switch and adjustable potentiometer used to control the Wizard-12 Control Board by manual control

Servo travel A-B, B-A
Switch Control servo movements
Pontentiometers set servo travel positions A and B

2 - Position Switch - Servo travel A-B / B- A positions
Switch configured as On - Off
Switch mounted on PCB board

PCB boards have wire terminal blocks for quick easy connections with on board adjustable potentiometers for servo control

10K Ohm slide and rotary potentiometer with wire terminal blocks.

Slide Potentiometer Board Size:
3-1/8" L x 1" W x 1-1/2" H

Rotary Potentiometery Board Size:
1-1/2" L x 1" W x 1-1/4" H

Micro Joystick attaches to Puppet 3 / Joystick Controller board, for manual programming and control.

Board includes 2-channel micro joystick, micro buttons on board.

Joystick is fully functional similar to full sized joystick Micro buttons function as thumb or trigger button similar to full size joystick,

On board DB15 Male connector attaches directly to Puppet 3 / Joystick controller board.

Micro Joystick can also be connected to optional joystick wire adapters for extended control away form puppet-3 joystick controller board

Puppet 3 / Joystick Controller Board , optional wire extenders not included

Micro Joystick can also be connected to optional joystick wire adapters for extended control away form puppet-3 joystick controller board

On board DB15 Male/ Female connectors
Wire Terminal Blocks for Joystick wire connection

On board DB15 Male connector attaches directly to Puppet 3 / Joystick controller board.

DB-15 Wire Cable, Puppet 3 Control Board, Joystick Modules not included

This unique board makes connecting a DC motor setup easy and quick.
Simply connect two remote relay outputs to the motor logic board inputs, power to the board, and a dc motor and you have a full functional CW / CCW operating motor board with limit position switch inputs, emergency stop switch protection

Board has connection for limit switches, emergency stop switch, remote relays.
On board LED's indicated motor direction, and power status
Quick power jack connector for motor power hook-up
Terminal blocks for wire from remote relays, motor connection
Connect this board to a Wizard - 9 controller and you get a programmable
motor controller with CW/ CCW motor control.

( Power supply, motor, and switches not included )

This specialzed board makes connecting a small DC motor, limit switches an easy and quick setup.
Simply connect two remote relay outputs or manual control switches to the motor logic board inputs, 2-Limit switches, power to the board, and a DC motor and you have a full functional CW / CCW operating motor board with limit position switch inputs.

Board has connection for limit switches, motor, power
Tr-Color LED indicates which direction motor is rotating
RED Power LED status lights
Small Board Size
Quick power jack connector for motor power hook-up
Terminal blocks for wire from remote relays, motor connection
Connect this board to a Wizard - 9 or Wizard 4 controller and you get a programmable motor controller with CW/ CCW motor control.
Connect this board to RF Receive and you get a wireless motor controller with CW and CCW motor control from Key Fob hand controller.
Connect to a 12 VDC power supply, switches and you have get a manual operated motor rotation controller wirh direction control.

Board Power Supply =12 Vdc
Motor Power Supply 1.0 Vdc to 12.0 Vdc

( Power supply, motor, limit switches, control relays, switches not included )

1- CH Relay Board - A Size:
1-3/8" L x 1-1/8" W x 1/2" H
SS Relay Rated:12 Vdc at 4 Amp

2- CH Relay Board - B Size:
1-7/8" L x 1-1/2" W x 1/2" H
SS Relay Rated: 12 Vdc at 4 Amp

1- CH Relay Board - C Size:
1-3/8" L x 1/2" W x 1/2" H
SS Relay Rated: 12 Vdc at 4 Amp
NO LED, Mounting Holes


Example use of SS Relay Modules

Relay module has one Solid State Relay output with wire terminal strips for quick device hookup.

Relay module is designed to connect with the Wizard, and Puppet Control family of interface boards or any 5 Volt dc power source to operate.
Relay can also be used to trigger BPE digital sound boards.

Module requires 5 volt input at 20 mAmp to operate
Board has input and relay output wire terminal connections

Relay rated for 12V DC at 4 Amp ( N.O. Normal Open )

Optional LED status indicator for Solid State Relay ON and OFF mode.
Wire Terminal strip for easy connection of other devices to the relay output.
Solid State Relay isolation from Load and Control Signal
Small board sizes.

OptionSS Relay- A
1- CH Relay Board - A Size: 1-3/8" L x 1-1/8" W x 1/2" H
SS Relay Rated:12 Vdc at 4 Amp

OptionSS Relay- B
2- CH Relay Board - B Size: 1-7/8" L x 1-1/2" W x 1/2" H
SS Relays Rated: 12 Vdc at 4 Amp

OptionSS Relay- C
1- CH Relay Board - C Size: 1-3/8" L x 1/2" W x 1/2" H
SS Relay Rated: 12 Vdc at 4 Amp
NO LED, Mounting Holes

Relay module has one Solid State Relay output with wire terminal strips for quick device hookup.

Relay module is designed to connect with the Wizard, and Puppet Control family of interface boards or any 5 Volt dc power source to operate.

Module requires 5 volt input at 15 mAmp to operate
Board has input and relay output wire terminal connections

SS Relay = Bi-polar Transistor Output Configuration

Relay rated for 60V DC at 1 Amp

Incorrect use or mishandling of these AC Voltage products could result in serious personal injury or death, possible physical damage of the product, faulty operation and other potential dangerous hazards. If you are not sure how to correctly wire or use these products, then STOP and seek professional qualified assistance. Use these products at your own risk.

Use these AC Voltage product at your own risk.

Warning - do not touch electrically charged parts such as the circuit board, power terminals, power cord wire ends or open electrical sockets. Doing so may cause electric shock resulting in serious personal injury or even death.

Warning - make sure the product has been correctly wired before turning the power ON and check to see that all wires are firmly connected to the terminals / sockets. Failure to do so could cause electric shock, fire hazards or result in physical damage of the product and serious personal injury or death.

Warning - before wiring, removing or mounting the product, be sure to turn the power OFF. Failure to do so may cause serious personal injury, physical damage of the product. Do not disassemble the product. Doing so could cause electric shock or faulty operation.

Use the product within the operating ranges recommended in the specification (voltage, amp loads, directions) Failure to do so might cause faulty operations, fire or other hazards.


By law, in no event shall Blue Point Engineering LLC be liable for any claim for incidental, consequential damages or any injuries sustained due to the use of or improper use of these AC voltage products These products should NOT be used for any applications that could cause injury, dangerous / hazardous situations or consequential damages or other hazards.

Use these AC Voltage product at your own risk.

By purchasing any BPE product, the buyer signifies agreement to all these terms of sale, safety warning, cautionary notices and will not hold Blue Point Engineering, LLC responsible for any liability for these AC Voltage products that were used at your own risk.