Board Size: 4-1/4" L x 2-7/8"
Wizard Board is pre-assembled and tested.
Controller has 7-bit Resolution.

Wizard - 1 Board Document

Application Note

Product Video

The Wizard - 1 Board is a small 9 Volt dc powered interface board that will record and playback up to 5 minutes of servo motion for 4 standard 5 Vdc hobby R/C type servos and control 4 digital switched ON and OFF outputs at +4.5 Vdc (100 mA) per channel.

The Wizard - 1 board incorporates many features such as looping playback servo motion with variable delay between loops. An auto start-up on power option and on board connector for remote activation switching such as a PIR sensor, contact switch or mat pressure pad to initiate playback.

Recording sessions are built up on a channel by channel process - no complex programming is required. During recording, all previously recorded channels are re-played to aid synchronization the current channel being programmed. Programming is easily done, with a set of push button keys and control potentiometer built onto the board.
No host computer or other programming device is needed to operate the board, Board has 7-bit Resolution.
Programmable Recording time - 5 Minutes

Power supply, Servos, not included.
( 9 Volt dc @ 2 Amp power supply needed )

The Wizard- 4 Controller Board or Programmable
4 - Channel Relay module will record and playback up to 25 minutes of controlled ON and OFF action for1 - 4 Outputs Relays.

The board incorporates such features as looping playback, variable delay between programmed routines, auto loop, auto start-up on power up, a connection terminal for remote switch activation by manual switch, PIR sensor, pressure pad, etc, to activate playback.

Recording sessions are built up on a channel-by-channel basis - no complex programming needed, or connection to a host computer to program routines. Board has many other features including on-board programing and function selection switches, Sync output, EEPROM protection, direct digital output pins, optional user selected jumper relay activation or power down setting.
The relay contacts are rated at 30 Volt DC @ 2 Amps.
Quick wire terminal blocks are built on-board for each relay, with a common connector jumper option.
Programmable Recording time - 25 Minutes
Programming is stored in EEPROM
Board has 7-bit Resolution.
Board is powered by a 9 Volt regulated power supply connected to the on-board 2.1mm socket.

Supplied built and tested.
( Regulated 9 Volts dc power supply not included )

Board Size:
3-4/8" L x 1-3/4" W x 1/2" H
Board is pre-assembled and tested.

Wizard - 6 Document

Application Note

Product Video

The Wizard - 6 Controller is a Random and Pulse motion Servo Controller.

The controller board will operate two servo channels each with there own unique random servo motion outputs and one channel with variable speed and time pulse motion servo output.
The controller allows for setting the range of each servo's travel motion limits, along with adjustable servo speeds and random time rate features.

This controller is excellent for creating random moving eyes (Left / Right - Up / Down) and head motions, eyelid blinks or in other effects where automated random servo motion is needed using a self-contained servo motion driver board. No programming is required.
Board operates from a regulated 9 VDC @ 2 Amp power supply.

( Power supply, servos not included )

Board Size: 4" L x 3" W x 1/2"H
Mechanical relay rated 30V @ 2Amps

Controller requires 9 Vdc power.
Board is pre-assembled and tested.

Controller Instructions

The Wizard 9 board will record and playback up to 25 minutes of action for up to 2 digital / relay outputs. The board also incorporates features such as looping action with variable delay between loops, auto start-up on power up and a connection interface for a PIR, remote switch or pressure pad to initiate playback.

Specifications:

2 Digital channels- either 0/5V @ 100mA outputs or mechanical relay rated 30V @ 2Amps to wire terminal blocks,.
On board Potentiometer to determine the time delay between play loops during automatic loop play- adjustable between 0 and 65 seconds.
Digital 1, Digital 2 on-off, NEXT, PLAY and RECORD buttons.
Record enable/disable jumper protection.
Programmable Relay Recording time - 25 Minutes
AUTO-PLAY and LOOP-PLAY switches
Sync output for multi board operation
REMote start option- for interfacing to pressure pads / PIRs switches, relays, manual start buttons, etc.
REM polarity select jumper- start on either +5v or 0V condition.
Board operates from 9 Vdc power supply
( 9 Vdc Power Supply, not included.)

Manual operated servo driver board will move a R/C servo in response to hand held remote slide or rotary position potentiometer input.

Specifications:
1 - channel manual servo control.
Servo output 1 to 2msec pulses.
Servo Travel A-B limits can be easily set.
Servo quick pin header connection.
Wire terminal block for remote potentiometer control.
Servo Travel 0 - 90 Degrees.
Quick Power connection
Operates from 7-9 Vdc @ 1 Amp power supply
Note: Controller board requires Potentiometer for operation.
( Board uses a 5 - 10K ohm potentiometer)
( Power Supply, not included.)
( Remote potentiometer not included )
( R/C servo not included )

Small controller for single servo control with up to 4 minutes recording time, loop playback with variable time delay between loops, auto start-up and easy recording features. Several modules may be daisy chained together and controlled from one master module.

The Puppet servo controller includes the following features:

- Single channel servo control
- Up to 4 minutes recording time
- Small modification to board, allows a servo to be
controlled by a hand push button switch, great for
Costume Animatronic Head control.
- Programmable Servo Recording time - 4 Minutes
- Full 180 degree rotation pulse train (for servos that can physically rotate 180 deg)
- Looping play with adjustable time delay between loops Record edit function
- Synchronization pulse for multiple unit operation

( 5 Volt dc power supply and Servo not included )

Small controller for single servo control with up to 4 minutes recording time, loop playback with variable time delay between loops, auto start-up and easy recording features. Several modules may be daisy chained together and controlled from one master module.

The Puppet Controller has an additional digital channel with a 1A @ 24 Vdc rated relay.
Record your servo channel first and then superimpose the digital channel whilst the servo is playing
The Puppet servo controller includes the following features:
- Single channel servo control
- Programmable Servo , Relay Recording time - 4 Minutes
- Full 180 degree rotation pulse train (for servos that can physically rotate 180 degrees)
- Looping play with adjustable time delay between loops Record edit function
- Synchronization pulse for multiple unit operation

( 5 Volt dc power supply and Servo not included )

.YouTube Videos of Animatronic
Characters using Puppet Controller

The Joystick Servo Controller is a dual channel servo controller capable of direct manual servo, relay control and with recording option of up to 13 minutes of servo and relay action, interfaced to a standard game joystick.

The board features loop playing with variable delay, synchronized playback, can be linked with several other boards for multiple servo applications, has servo movement limit setting and a single relay channel output.

Joystick forward and backwards controls servo one motions.
Joystick left and right controls servo two motions.
Thumb button = playback / recording
Trigger button = relay ON/Off control.

Pressing down and holding the Thumb button will activate the record option where joystick / servo motion is recorded to an on-board EEPROM for playback up to 13 minutes.
Playback motion can be later activate by pressing the finger button, anytime, even between manually servo control.
Board power is provided by plug-in wall unit, or optional mobile power supply and will operate both joysticks and servos.
Programmable Servo, Relay Recording time - 13 Minutes.

NOTE: Analog Joystick with DB-15 connector required. Will not work with new USB type joysticks.
( 9 Volt dc Power supply, Servos and Joystick not included )

Joystick Adapter Kits- Build Your Own Joystick Interface
( Joystick, power supply, servos, not included )

Joystick Controller Document

Joystick Controller Applications

Product Video



Puppeteer 3 Micro Joystick Interface Module

This small board will be found invaluable for projects and models using R/C type servos.

Test and calibrate hobbyist "R/C - Radio Control" type servos.
- Manual and Automatic Modes
- Variable speed 90 degree sweep facility
- Stand alone servo sweep function for animations
- 0 and 90 degree calibration LED Light (1ms and 2ms pulse widths check)
- Calibration LED light every 15 degrees

In Automatic mode, Servo-Check produces a pulse stream that makes the servo traverse smoothly through 90 degree at a speed determined by the potentiometer setting (approx 0.5 to 5 secs / 90 degree ).

Advanced users can add 2 standard 10k linear potentiometers to adjust the end stops for a simple, stand-alone animatronic controller module.

In Manual mode, the servo position is fully adjustable from 0 to 90 degrees by using the thumbwheel. Manual mode generates a standard servo pulse stream. The width of the pulses varies between 1.0msecs and 2.0 msecs depending on the position of the potentiometer. Turning the potentiometer fully to either end of its travel will cause the LED to light indicating that either a 1.0 or 2.0 pulse width which should correspond with a servo angle of either 0 or 90 degrees. Additionally, as the potentiometer is turned, the LED will light at positions corresponding to15, 30, 45, 60 degrees and 75 degrees , thereby providing a field calibration setup.

Works from standard 5-6 VDC supply and includes 3-pin header for all standard servos.

Supplied built and tested, ready for immediate use.
( 5 Volt Power supply and Servo not included )

This unique BPE exclusive small custom controller board was designed to operate a standard R/C servo in several user modes. Mode one is running the servo to a programmed minimum and maximum limit by the push of button 1 or 2. The user can activate button 3 to play back a previously recorded user sequence of servo movement (up to 15 minutes recorded time).

Three Buttons on the control board or remote buttons determine what the servo will do ­ (1) move to the minimum position, (2) move to the maximum position or to (3) continuously loop the user recorded sequence. On board potentiometer / program button and EEPROM allow user to record and store servo routine needed (15 minutes )

The servo is connected to the board either by the 3-pin servo connector or by the servo terminal block. The board requires a power source 7.5V dc to 9V dc at 800 mA or greater. Power can be hooked to the board either by a 2.1mm power connector or by the alternate power terminal wire block.

Example Application 1: " Moving Wings "
Servo Position 1 ( Switch-1 ) Fairy Wings Closed
Servo Position 2 ( Switch-2 ) Wings Fully Open
Servo Position 3 ( Switch-3 ) Wings moving back and forth in motion routine programmed by user.

Example Application 2: " Monster Jaw Mandible "
Servo Position 1 ( Switch-1 ) Mandible Closed
Servo Position 2 ( Switch-2 ) Mandible Fully Open
Servo Position 3 ( Switch-3 ) Mandible moving back and forth in an attack or eating effect.

Board can operate by battery power or standard wall power supply adapter

(7-12 Volt dc power supply, battery, switches, Servo and wing mechanical mechanism not included )

Board Size:
4-3/4" L x 4-1/4" x 1" H

This unique board will allow the control of 4 servos manually via remote 10K potentiometers or by Wizard -1 Board control. The input (pots or Wizard Board) is selected by on-board slide switch or dry contact closure to the Remote Input Selection terminal block. When switched to (M)anual, the 4 servos are independently controlled by the remotely mounted pots. Minimum and maximum limits can be set for each servo but these limits are only in effect when the board is in (M)anual control. When in (W)izard mode, the Wizard Board will handle limits for the servos. There is an on-board SS relay that can either be activated by dry contact closure at the Remote Relay Trigger terminal block or by pressing the small pushbutton located next to the relay.

( Power supply, 10K potentiometers, Servos, Wizard -1 Board not included )

This unique controller board was designed to allow the use of 2 on-board joysticks to control 4 servo motors. The minimum and maximum limits of movement for each servo can be programmed and are stored in non-volatile memory.

There is also a SS relay that is activated by a toggle switch.
Relay rated at 2 Amps

The board has separate power entries for board power and servo power with the ability of using a remote switch to turn either on or off.


Board Requires 9 Volt dc @ 1 Amp power supply.
Board Requires 5 Volt dc @ 5 Amp power supply.

( Servo motors , Power supply - Not included )

The AutoTalk -E2 board is similar in function with all the exact features of the original AutoTalk board developed several years ago for professional animatronic clients, in that it moves an R/C type servo in response to either an audio input signal from any standard CD player, tape recorder, sound source, but now has jumper setting for greater sensitivity in using the board from a sound source with low signal input, such as found on a digital sound chips or direct connected mic amplifier and dynamic microphone setup. The board has an on-board voltage regulator for using a variety of voltage sources including the use of a battery for remote applications, a quick connector for connecting power, LED power status indicator and enhanced output to operate a standard R/C servo with greater response. The controller includes the function to set both the servo end travel points, an important feature when working with various mouth jaw sizes, the servo arm direction of travel can also be quickly changed by an on-board jumper and the sensitivity of the audio input signal through the improved on-board gain control have also been enhanced for greater response.

( 9 Vdc Power supply, servos, sound source not include )

Note: When using a Dynamic Microphone that is not amplified, an optional Dynamic Microphone Amplifier is needed between the mic output and AutoTalk audio input.

The Digital Sound Board - ProE is a full featured mono digital sound board with many unique features and applications.

Up to 4 - minutes recording time for 1 - mono channel or multiple mono channels (1-9). Sounds can be recorded to from any sound source, including a computer connection with audio output.
On-board 7 - watt mono amplifier with volume preset control for external 8 ohm speaker monitor. Line output jack for connection to large remote amplifier and speaker. Line input recording jack, for easy connection to sound input source. Playback (channels 1-6) under manual control, sensor, relay, automated controller board activation or direct computer control (all channels 1-9). Optional Sequence, Random or immediate On / Off playback board features available.

The supplied 4 - minute ISD sound chip has a great frequency response up to 3.4 KHz. and a audio sample rate of 8.0 KHz. Audio can be re-recorded up to 100,000 times and can be stored up to 100 years. Board is excellent for many Animatronic, Robotic and Haunted Industry applications where quality audio is required on a single easy to use device. Board is very easy to set-up, record to and use through on-board jumpers, audio in / out jacks and status operation LED's. Sound IC chip can be removed, for upgrade or saving of sound files.

Total message lengths up to 4 minutes.

Power supply, speaker, switches, amp, sound source, audio cables not included

Record and playback 1 - 8 audio channels in manual switch, or relay mode with individual channel selection or 8 channels in random or sequence playback mode with a single switch, relay or input signal, all with one unique digital memory sound chip and controller.

Total message lengths up to 60 seconds.

Microphone and amplifier chip ( 250mW/ 8 ohms ) are incorporated on the sound board.

Each sound channel can be activated by it's own switch, relay or control signal connection, ( 1-8 ) or multiple channels (1-8 ) can be played in sequence or random with a single switch, relay or control signal input.
A single 60 second recording or multiple length recordings can be easily done using on-board microphone.

The Vegas Sound Board has quick connect audio in / out jacks and power jack for fast setup, an On and Off power switch, LED status light showing power, playback and record mode. Optional recording switch, speaker, power connection board solder pads for hard wiring to board. Stabilized audio circuitry to reduce electronic, environmental noise. The board also can be connected to any of the RF interface boards quickly through a ribbon connector pin header setup.

Use in message boards, warning devices talking animatronic characters, train sets, model effects, costumes or robotics,

( Power supply, switches, amp and speaker not included )
( RF unit, audio connection cables not included )

Click on image for a closeup view

3-1/4" Long
2-5/8" Wide
1-1/8" High

Operating / Setup Instructions

Here is a very simple audio controller that when triggered by pressing the single on-board button or by dry contact closure at the trigger terminal, will cause the player to play back 1 to 10 MP3 files that are stored on a USB flash device (USB pen drive not included). These MP3 files can be of any size up to the capacity of the USB flash device. You can have any number of files up to 10 on the flash device.

There are 2 modes of operation provided ­ Sequential and Random.

In Sequential Mode, the player will play the files back sequentially from file000.mp3 to file009.mp3 (or whatever your last file is), one file at a time each time the board is triggered. After it has played the last file, it will go back to file000.mp3 and start over.

In Random Mode, it will pick one of the files to play back at random. It will pick a new file each time the board is triggered. The board will wait until the file has finished playing before it can be activated again.

Remote Sensor boards can be added to trigger the audio playback board automatically, or manual switch can be used to start playback

This MP3 controller can be used in a prop, with an animatronic character, puppets, information display exhibit , at museums, zoos, as public information boards and other areas to play very high quality stereo audio sound every time it is activated.

( 9 -Vdc power supply, speaker, remote amp, switch, audio cables, USB pen drive - not included )

Click on images for a closeup view of boards

Operating / Setup Instructions

Main Sound Control Board
3-1/2" Long x 3-3/8" Wide x 1-3/8" High

Remote Switch Board
4-1/8" Long x 2" Wide x 1/2" High

Ribbon Connection Cable
3- Feet

Remote (SS) Solid State Relay - 2 Amp Board
5" Long x 2" Wide x 1/2" High

Remote Solid State Relay - 3-10 Amp Board
5-1/4" Long x 2-7/8" Wide x XX" High

Solid State Relay Example 1
Solid State Relay Example 2

Advanced full function MP3 audio control board, when triggered by activating the remote channel 1-10 switches or by dry contact closure (Relay), will cause the player to play back 1 to 10 MP3 files that are stored on a USB flash device and turn on a remote Solid State 2 Amp Relay board corresponding to the sound channel activated 1-10.

The audio (Stereo) MP3 files can be of any size up to the capacity of the USB flash device. You can have any number of files up to 10 on the flash device.

There are 3 modes of operation provided ­ Manual, Sequential and Random channel selection.

Manual mode any channel 1 - 10 can be played back by selecting the remote switch corresponding to the sound channel, along with the corresponding solid state relay being activated.

Sequential Mode, the player will play the files back sequentially from file000.mp3 to file009.mp3 (or whatever your last file is), one file at a time each time the board is triggered, along with activating a Solid State Relay for that channel. The Relays will stay activated for as long as the sound file is playing. After the board has played the last file, it will go back to file000.mp3 and start over.

Random Mode, the control board will pick one of the files to play back at random, along with activating the corresponding solid state relay. It will pick a new file each time the board is triggered. The board will wait until the file has finished playing before it can be activated again.

This MP3 controller can be used in a prop, animatronic character, puppets, information display exhibit to play very high quality stereo audio sound every time it is activated and activate remote lighting, effects, animatronic controllers or other devices connected to the remote relay boards.

There are two different remote relay boards available to use with the playback board. A 5-Ch Solid State 2 Amp Relay board or a user setup relay board that can use 1-5 solid state relays from 3 to 10 Amp in size provided by the user.

The user setup Remote Relay Boards can be combined with the same size Solid State Relays or different Solid State Relays can be mixed with the Solid State 3-10 Amp board.
Each relay board has 5 solid state relays, so 1-5 or 1-10 relays can be used, as needed.

Main Sound Control Board can be operated without attached solid state relays if needed.

Relay Output ports can be used to trigger other devices
Port provides 4.5 Vdc at 20 mAmps out

Remote Sensor boards can be added to trigger the audio playback board automatically, or manual switches can be used to playback channels.

Several board configuration setup options available

( 9 - Vdc power supply, speaker, remote amp, switches, switch board and cable, audio connection cables, USB pen drive, Solid State Relays and audio cables - not included )

Unique board will control 6-Strobe LED's, 6-Fading LEDs, and 8-Switched On and Off LED's by remote activation.
Board has input connection for remote activation by relays, switches or controller board.
Each Switch Bank will control one effects section
LED Wire terminal blocks for quick connection
Board requires 9 Vdc @2 Amp Power supply



( Power supply, LED's not included )

Unique board will control 6-Beacon LED's, 10-Chasing LEDs by remote activation.
Board has input connection for remote activation by relays, switches
or controller board.
Each Switch Bank will control one effects section.
LED Wire terminal blocks for quick connection
Board requires 9 Vdc @2 Amp Power supply



( Power supply, LED's not included )

Unique board will control 24 LEDs by remote activation.
Board has input connection for remote activation by relays, switches or controller board.
Each Switch Bank will control 8 LED's, three switched banks available
LED Wire terminal blocks for quick connection
LED's require voltage drop resistance when connected to board.
Resistors not on control board.
Board requires 9 Vdc @2 Amp Power supply



( Power supply, LED's not included )

Unique board will control 2-Channels Switched On and Off Power Driver's by remote activation. The two channels can be connected to any Fiberoptic Light source and fiberoptic cables.
Each Switch Bank will control one fiber section
Board has input connection for remote activation by relays, switches or controller board.
LED Wire terminal blocks for quick connection
Board requires 9 Vdc @2 Amp Power supply



( Power supply, LED's not included )

Optical fibers attached to single 5mm LED source.
Light shines out end of fibers. Fibers can be cut to various length as needed, glued, wired, or taped to secure in projects. Optical Fibers are attached to LED through special metal LED and fiber holder.

This module is great for floral arrangements, centerpieces, holiday projects, posters, art projects and even model builders needing unique lighting effects.

Module operate on batteries, wall adapter
( any 9Vdc - 800mA power supply )

LED power wire - 12" Long - Black (-) / White (+)
20 - Optical Fibers -Approx: 21" Long

BLUE, RED, GREEN Colors available

Resistor included for 9 Vdc power supply

Instruction manual, application guide.

Light source: one - 5mm LED

LED and Fiber holder Size: 1- 3/8" L x 3/8 W

( power supply , batteries, projects not included )

Unique board will control 3-Channels Switched On and Off Power by remote activation. The three channels can be connected to any Light source such as LED's, LUXEON LED's, Fiberoptics, DC Light Bulbs.
Each Switch Bank will control one effects section, each effects section can operate 2 outputs (6 total outputs available)
Board has input connection for remote activation by relays, switches or controller board.
LED Wire terminal blocks for quick connection
Board requires 9 Vdc @2 Amp Power supply



( Power supply, LED's not included )

If your unsure what to purchase but wish to start learning about the Luxeon LED modules, then try our Luxeon LED Starter Kit.

The kit comes with your choice of:
1 - Watt Luxeon Star LED module, you pick color.
1 - Small Heatsink with self-stick backing.
1 - Micro-2004 Driver and connection cable.
1 -"AA" Battery Holder, and Instructions.

Luxeon LED's available in
Red, Green, Blue, White Modules

.....................Kit Instructions

( "AA" Battery not included )

Connect this Microprocessor aided, solid state digital switch board to you radio control receiver and have the option of manually controlling a relay output ON or OFF with your R/C transmitter.

Solid state relay is isolated from R/C signals, and has automatic OFF feature when transmitter / receiver is powered OFF.
On board solder pads for Servo lead wire and Relay output connections. Micro LED status light.

Relay contact: Up to 20 volts, 9.0 amps VDC Max.
Powered by R/C receiver drawing only 13 ma.
Adjustable DIP switches provide four (4) threshold positions for relay with an on board LED to aid in setup and board status.
Switches off load if receiver signal is lost.

Relay contact: Up to 20 volts, 9.0 amps VDC

This module is designed to switch a single R/C channel control signal to four different set of servos individually or as any group 1-4.

Module allows each servo to be controlled independently from the standard control signal (PWM) but can be switched to control different connected servos.
Board can be configured to power servos of different voltages individually, or from one common power source, depending on power supplies used (1Vdc - 24Vdc)
Servos can be switched automatically on board by selecting slide switches, or switching between servos 1-4 can be controlled by remote relays or manual switch inputs to board.

Wire 3-pin header blocks, make hook-up to servos and connection to servo controller easy to do. Power block for quick setup of different voltages to servos.
Header blocks for remote switching source.

Requires power supply ranging from 7.5V to 24V DC at 100 mA for on board electronics and voltage from 1-24 Vdc for servo used.

Servos, servo controller and power supply not included.

Board Size:
4-1/2" L x 4-1/4" W x 1" H
Application Setup Overview

The board will switch 6 individual servo PWM signals coming from a R/C
Radio Control receiver or 6 individual servo PWM signals coming from a Wizard Board to 6 shared common servo lines when switched on / off by R/C
transmitter-receiver Ch 1

Board Size:
6" L x 4-5/8" W x 1" H
Application and Setup Overview

This board allows the use of an RC controller to select outputs for two servo inputs and control two SS relays. The Servo outputs and relays are controlled separately. Two servo inputs can be output to 6 different outputs. The RC joystick allows the user to select which of the 6 outputs to send the two servo inputs to. Moving the joystick left decrements the channel, moving it right increments the channel. The channel number selected is displayed on a 7 segment LED display. Once a channel has been selected, a 2 second time delay is started before enabling the outputs. After the delay has expired, the Channel Active Indicator (decimal point on LED Display) lights and the incoming servo signals are routed to the selected outputs. Power for the servos can be supplied by a single power supply (by inserting the shorting block next to the servo connector), or any servo can have a separate power source. This is attached at the terminal block just above the servo connector. In this case, the shorting block must be removed. All servo signals are optically isolated from the inputs.

The relays are also controlled by RC joysticks. Each relay is controlled by a separate joystick. Moving either joystick to the right will activate the associated relay. When the joystick is returned to the center, the relay is deactivated.

The board is powered by 12VDC and is attached to the Power Input Terminal block or the 2.1mm Power Jack. A terminal block is also supplied to allow the attachment of a remote switch which will bypass the on-board switch.

Stop servo creeping
Prevent servo creep in 360° servos
Mounts like a boosted extension

Prevent the creep that is common with 360° modified servos used as robot drives. The Servo Neutralizer expands the dead-band range of the analog servo to compensate for occurences that cause the servo to wander beyond its neutral position.

The Servo Neutralizer increases the servo's dead-band range by 12hz causing the analog servo not to react to small signal variations.

The servo's range of motion is not affected. Mount the Servo Neutralizer just like you would a boosted extension. Each neutralizer comes in 24" lengths.

NOTE: Not Intended for use on Digital Servos, or servos with FET booster installed. The total amount of rotation control is dependent on the type of radio control or servo controller.

Extra range without distorting a servo signal.
Increase your range of servo motion to 180° instead of the standard 90°. The 180° Servo Stretcher doubles the range of your servo's motion giving you a full 90° of motion to either side of neutral with most servos. Works with any brand of analog servo.

The 180° Servo Stretcher doubles the distance between stops on the servo - effectively doubling the servo's range of movement without affecting the speed of the servo. Mount the 180° Servo Stretcher just like you would a boosted extension. Each stretcher comes in 24" lengths.

NOTE: Not Intended for use on Digital Servos, or servos with FET booster installed. The total amount of rotation is dependent on the type of radio control or servo controller. Results may be slightly less than 180° or slightly more. If it is slightly less, using full trims will allow more rotation.

CAUTION
Use caution when working with the Servo Stretcher, as some servo's have actual mechanical stops built into the servo that prevent extended rotations. Trying to exceed this stop will damage the servo. This product is not to be used with servos that offer more than 90° rotation from the factory or any brand of digital servos.

This inline servo signal processor lets you slow down the travel movement of the servo, without effecting the servo performance

The controller can be set for 1.7 sec, 2.2 sec, 3.8 sec and 6.5 sec delay.
Controller has Futaba J connectors, male and female.
Supply Voltage required 3.8 - 5.5 Vdc Max @ 7ma
Control Granularity: 200 steps full scale.
On board LED status indicator

It also doubles as a signal booster.

NOTE: Not Intended for use on Digital Servos, or servos with FET booster installed. The total amount of servo control is dependent on the type of radio control or servo controller used. Results may vary with different systems.

This Dual Adjustable Servo rate slower has the ability to indepenantly slow down two servos. A small potentiometer allows the servo end and end speed to be adjusted from less than 1 second to 5 seconds. The potentiometer also allows selection of the failsafe signal. When the rate reducer receives 10 bad signals in a row, it will default to failsafe mode and slowly move the servo to the failsafe position. This is especially important for Robot Combat gear

One or both channels can be used at any time.

The small potentiometer is adjusted in the following manner: The center is the fastest servo speed. Turning the potentiometer to the left or right will slow down the servo. Turning the potentiometer to the left will enable the failsafe signal to be 1.0ms. Turning the potentiometer to the right will enable the failsafe signal to be 2.0ms.

Information:
Weight: 2.8g
Current Draw: less than 5ma
Operating Voltage: 3.5 to 5.2 volts

NOTE: Not Intended for use on Digital Servos, or servos with FET booster installed. The total amount of control is dependent on the type of radio control or servo controller.

This 24" Servo Extension Booster for Futaba J servos allows you to place your servos farther away from the signal source in animatronics and robot projects.

Mounts like a normal servo extension between controller and servo.

The Servo Reverser will actually reverse the direction of the R/C servo motor rotation.
Servos can now be mounted with symmetry in your project.

Information:
Weight: 1 gram
Size: 8mm x 44mm x 5mm (average)
Power consumption: 4 mA

Abilities:
Accuratly reverses the servo signal so the servo turns in the opposite direction.
Over 800 steps of signal input/output resolution .

NOTE: Not Intended for use on Digital Servos, or servos with FET booster installed. The total amount of control is dependent on the type of radio control or servo controller.

Servo Jumper - Male-Male connector ends.

22 AWG Servo Lead - Hitec Connectors - 6" jumper
22 AWG Servo Lead - Universal Connectors -12" jumper

Connect this unique duo board to you R/C receiver or any Wizard control board servo output and have the option of manually controlling a relay output ON or OFF with your R/C transmitter joystick or automated control when used with a Wizard board.
Board has jumper to invert manual joystick movement positions, Transmitter joystick activation set point LED with easy on-board adjustment potentiometer. On board jumper can be used to by-pass relay and send control output as direct voltage to external devices also. (1 -24 Vdc output )
Relay contact: 24 VDC @ 8 amps VDC
Transister Switch: 24 volts @ 9.0 amps VDC

(VDC output power supply not included)

Connect this Power VDC switch board to your R/C receiver or any Wizard Board Servo output and have the option of switching ON and OFF any user selected voltage (1-30 VDC) to remote connected device directly or to a remote add-on module.

Board will switch from 1 VDC to 30 VDC directly through on-board Power Transistor, to Wire Terminal Block.
Control board electronics is powered directly from R/C receiver or servo output, with quick connector and wire terminal block for easy set-up and control. Jumpers provide threshold positions with LED to aid in quick setup and calibration of board activation.
(VDC output power supply not included)

Board Size:
1-7/8" L x 1-7/8" W x 1/2" H
Application and Setup Overview

Connect this Microprocessor aided, solid state digital switch board to you radio control receiver and have the option of manually controlling two relay outputs ON or OFF with your R/C transmitter joystick.

Board Size:
2-1/2" L x 1-7/8" W x 1/2" H
Application and Setup Overview

This board allows the activation of two Solid State 2-Amp Relays by using the standard R/C Transmitter joystick. It has 4 modes of operation that are selected by the placement of 2 jumpers. The board is powered by the +5V coming from the servo connector.

Mode 1: Pulse Mode
When the joystick is moved to the left, Relay 1 activates and stays activated as long as the joystick stays in the left position. When the joystick returns to the center position, the relay deactivates. When the joystick is moved to the right, Relay 2 is activated and stays activated as long as the joystick stays in the right position. When the joystick returns to the center position, the relay deactivates.

Mode 2: Toggle Mode
When the joystick is moved to the left, Relay 1 is activated (toggled on) and stays on even when the joystick is returned to the center position. The relay is deactivated (toggled off) by moving the joystick to the left a second time. When the joystick is moved to the right, Relay 2 is activated (toggled on) and stays on even when the joystick is returned to the center position. The relay is deactivated (toggled off) by moving the joystick to the right a second time.

Mode 3: Double Pulse Mode
When the joystick is moved to either the right or left, both relays are activated at the same time and stay activated as long as the joystick is in the left or right position. As soon as the joystick returns to the center position, both relays are deactivated.

Mode 4: Double Toggle Mode
When the joystick is moved to either the right or left, both relays are toggled on and remain on when the joystick is returned to the center position. When the joystick is moved to either the right or left position a second time, both relays are toggled off.

Hand Held Transmitter:
Type: RF radio(315MHz)
Transmitting Distance: 200m
Supply Power: A23 DC12V Battery
Encode: Fixed code
Momentary: Press-ON, Release-OFF
1 - Channel Soft Button
Expanding Antenna (2-3/4" long)

Receiver Module:
Type: RF radio (315MHz)
Operating voltage: 12V
Decode: Fixed code
Control Type: Momentary
Relay: 3A 120VAC / 24VDC
Wire Terminal Blocks for quick set-up

( 12Vdc Power supply for Receiver not included )

Application Example

Hand Held Transmitter:
Type: RF radio 315MHz
Transmitting Distance: 200m
Supply Power: 27A12V Battery
Encode: Fixed code
4 - Channel Soft Button
Expanding Antenna (1-3/8" long)

Receiver Module:
Operating Voltage: 5 VDC
Operating Current: 5 mA
Receiving Sensitivity: -103 dbm
Operating Frequency: 315 MHz
Transfer Rate: 4.8K
Modulating: AM
Output: TTL
Control Mode: Momentary
Coding Type: Fixed Code,

( 5VDC Power supply for Receiver not included )

Hand Held Transmitter:
Type: RF radio(315MHz)
Transmitting Distance: 200m
Supply Power: 27A12V Battery
Encode: Fixed code, Soldering.
4 - Channel Soft Button
Expanding Antenna (1-3/8" long)

Receiver Module:
Type: RF radio (315MHz)
Operating voltage: DC12V
Decode: Fixed code, Soldering
Control Type: Momentary
Relay: 3A 24VDC / 3A 120VAC

( 12VDC Power supply for Receiver not included )

Designed to work with the Sound Board Pro Series

Hand Held Transmitter:
Type: RF radio(315MHz)
Transmitting Distance: 500m
Encode: Fixed code
6 - Channel Soft Button
Expanding Antenna (5-3/8" long)

Receiver Module:
Type: RF radio (315MHz)
Operating voltage: 12V
Decode: Fixed code, Soldering
Control Type: Momentary
Relay: 3A 24VDC / 3A 120VAC

( 12Vdc Power supply for Receiver not included )

RF to Sound Board Pro Application Example

Designed to work with the Sound Board 60 Series

Hand Held Transmitter:
Type: RF radio(315MHz)
Transmitting Distance: 500m
Encode: Fixed code
8 - Channel Soft Button
Expanding Antenna (5-3/8" long)

Receiver Module:
Type: RF radio (315MHz)
Operating voltage: DC12V
Decode: Fixed code, Soldering
Control Type: Momentary
Relay: 20A 14VDC / 10A 120VAC

( 12vdc Power supply for Receiver not included )
( Power supply for Receiver not included )
( Sound Board 60 Module not included )

Remote control of Sound and Motion Boards
Designed to work with the Sound Board Pro, or Sound Board 60 and any Wizard or Puppet Control Boards

Hand Held Transmitter:
Type: RF radio
Transmitting Distance: 500m
Supply Power: A23 DC12V Battery
Encode: Fixed code
12 - Channel Soft Button
Expanding Antenna (6-1/2" long)
Momentary: Press-On, Release-Off

Receiver Module:
Type: RF radio
Frequency: 315MHz
Operating voltage: DC12V
Decode: Fixed code
Control Type: Momentary or Toggle slectable by jumper
Relay: 12A 12VDC / 7A 120VAC

( 12Vdc Power Supply for Receiver not included )
( Sound Board Pro, 60 Modules not included )
( Wizard, Puppet Boards not included )

Servo Description - Click on the image above for Servo information

Catalog No.

-

Conversion Formulas

80 ft-lbs of torque. 80 ft-lb x (12 in / 1 ft) = 960 in-lbs (feet cancel out) 80 in-lbs of torque 80 in-lb x (1 ft / 12 in) = 6.667 ft-lb (inches cancel out) ft-lb = in-lb / 12 in-lb = ft-lb x 12

Heavy duty Ball Joints
Plastic Socket with metal ball on threaded connector
Size (4-40) and (2-56)

Unique servo system provides true linear output motion from a standard (Futaba) R/C type servo. The linear servo converts the 42 in-oz torque from the Futaba servo into more than 1-lbf (foot-pound-force) of push and pull, linear control horn throw of 0.5" to 0.75" depending on end point adjustment from the signal source but will not exceed 0.75" max.

Excellent for animatronics applications where push and pull cable, rod or direct linear motion applications are needed.

This servo has a Futaba ( J-type ) connector which attaches directly to any 0.1" 3-pin header. 5Vdc power required.

Horn Speed: Approximately 1.7 inches per second.
Servo size: Approx.- 1-5/8" L x 3/4" W x 1-7/8" H

Servo operated linear rack mechanism.

When servo is activated linear bar rack will move back and forth.

Flexible push rods, ball joints can be attached to plastic linear bar rack

With linear servo turned vertical, items can be raised or lowered.

Servo bracket has various mounting holes, for vertical, horizontal applications.

Servo Bracket, Gear and Rack are molded from white plastic material.

Clear Rubber Eyes with Veins
( 24mm )


White Plastic Eyes with Veins
( 24mm )

Incredible realistic looking acrylic half eyes in 24 mm sizes.

Each eye is a half sphere

2 Eyes per set.

These servo brackets will allow you to easily mount any standard size servo and then connect the bracket to a 2" PVC pipe in various angles needed.

Kit includes:
Servo Mounting Bracket and Support Block
Mounting hardware
Servo Linkage Hardware
Instructions / Application Overview

Brackets Kits comes as all WHITE plastic parts, can be painted with plastic paint, or Croma Key green or blue paint for video production.

With this complete kit you can build a mechanical eye module that will move the eyes left and right using the attached micro R/C servo.

By connecting the R/C servo to any of the optional control board you can create a fully programmable eye module with automated control and playback or to the Wizard-12 controller if you want to manual control the eye movements left and right.

The eye module is based on real Human Scale
Eye center to center = 2-1/2" (center iris to center iris)
Eye ball size = 24mm
(Plastic 1/2 Ball with realistic black iris and surrounding coloring)

Kit includes:
Pico R/C Servo (GWS)
Servo mounting bracket, support and hardware
Eye movement bracket with mounting hardware
2 - 24mm 1/2 ball realistic human eyes
Servo linkage hardware / parts
Instructions / application overview

Tools needed for kit assembly
(Not included in kit)
Screwdriver
Needle Nose Pliers
Drill and drill bit (3/32)
Super Glue- Thick or Gap Filling type
Sandpaper
X-Acto knife
X-Acto saw or Hacksaw

With this complete kit you can build a mechanical eye module that will move the eyes Left, Right, Up and Down using the attached standard R/C servos.

The eye module is based on real Human Scale
Eye center to center = 2-1/2" (center iris to center iris)
Eye ball size = 24mm
(Plastic 1/2 Ball with realistic black iris and surrounding coloring)

Kit includes:
Standard R/C Servos
Servo mounting bracket, support and hardware
Eye movement bracket with mounting hardware
2 - 24mm 1/2 ball realistic human eyes
Servo linkage hardware / parts
Instructions / application overview

By connecting the R/C servo to any of the optional control board you can create a fully programmable eye module with automated control and playback or to the Wizard-12 controller if you want to manual control the eye movements left and right.

This kit is similar to the Mechanical Eye Kit- A. With this complete kit you can build a Cyclops mechanical eye module that will move a single eyeball left and right using the attached pico R/C servo.

By connecting the R/C servo to any of the optional control board you can create a fully programmable single eye module.

Eye ball size = 24mm
(Plastic 1/2 Ball with realistic black iris and surrounding coloring)

Kit includes:
Pico R/C Servo
Servo mounting bracket, support and hardware
Eye movement bracket with mounting hardware
1 - 24mm 1/2 ball realistic human eyes
Servo linkage hardware / parts
Assembly guide / application overview

With this complete kit you can build a mechanical mouth module that will open and closed using the attached micro R/C servo.

By connecting the R/C servo to any of the optional control board you can create a fully programmable mouth module with automated control and playback or to the AutoTalk controller if you want to convert sound directly to servo motion control.

Kit includes:
Micro R/C Servo
Mouth mounting bracket, support and hardware
Mouth movement bracket with mounting hardware
Realistic mouth with teeth and free movement animation tongue
Servo linkage hardware / parts
Assembly guide / application overview

NOTE: Mouth Kit comes as all WHITE plastic parts, can be painted with plastic paint, or Croma Key green or blue paint for video production.
Servos come black in color.

....... Example of Finished Mouth


.. YouTube Video Mouth Opeating
. ...........New Enhanced Version

Discharge standard C02 cartridge with a servo output

Servo and Bracket attache to cylinder. When servo is connected to R/C receiver or Wizard Board servo port, user can discharge cartridge as needed.

(C02 Cartridge, R/C Receiver, Wizard boards, Hoses not included)

With this kit you get a heavy duty servo and manual servo controller

Kit includes:
Manual Servo Controller - Wizard -12 Board
Slide Potentiometer Board
Heavy Duty Servo Arms.
Dual Ball Joint Link (2-56 size).
Universal Servo Mount.
Heavy Duty Standard Servo
9 Vdc Power Supply - Wall adapter

(J-connector on servo wire)
Mask, Character not included.
( Note: Hardware may vary from image shown, as new items are made available)

Build your own animatronic talking character from the supplied kit.

With this kit you can build a character that will have a moving jaw that is controlled from any 1 volt peak to peak sound input, such as from a CD player, microphone, stereo source. ( 1 volt line level required )

Kit includes:
Standard R/C servo.
Servo linkage hardware kit.
AutoTalker E servo controller.
AutoTalker controller instruction manual.
9 Vdc regulated power supply (wall type)

( Requires audio source ( CD player, Stereo, Mask, Character ) not included )
( Note: Hardware may vary from image shown, as new items are made available)

Click on image for a Closeup

Hand Transmitter Size:
Approx 2-1/2"L x 1-1/2"W x1/2"H

Receiver Size:
Approx 1-3/4"L x 1-1/2"W x1-5/8"H



Example Connection to Sound Board 60E

RF to Sound Board 60 Series Application Example

Use this system to remote control the Sound Board VEGAS from a remote location up to 100 feet away.
It can be set up to playback channels 1-8 in random or sequence mode, or playback a single long channel each time the remote hand held is triggered.

This unique module connects a 1 - Channel Remote RF system quickly to the Sound Board VEGAS. The on board power supply connector provides power to operate the RF receiver directly at 12Vdc.

A header connector on a 4" ribbon cable quickly connects the control pins of the SB VEGAS to the 1- Ch RF Remote Receiver.
A set of jumper pins, allow the SB VEGAS to be placed into the Random, Sequence or Ch -1 playback mode.

An on board button allows the SB VEGAS to record sounds quickly without disconnecting the interface. The button also serves as a test function to playback sound and check the Sequence and Random board modes.
Board has RF receiver power indicator LED.

Board requires a 12Vdc @ 500mA power supply

Hand Held Transmitter:
Type: RF radio(315MHz)
Transmitting Distance: 200m
Supply Power: A23 DC12V Battery
Encode: Fixed code
Momentary: Press-ON, Release-OFF
1 - Channel Soft Button
Expanding Antenna (2-3/4" long)

Receiver Module:
Type: RF radio (315MHz)
Operating voltage: 12V
Decode: Fixed code
Control Type: Momentary
Relay: 3A 120VAC / 24VDC
Wire Terminal Blocks for quick set-up

( 12Vdc Power supply for Interface not included )
( Sound Board VEGAS Module not included )

Use this system to remote control the Sound Board VEGAS from a remote location up to 100 feet away.
It can be set up to playback channels 1-8 in random or sequence mode, or playback a single long channel each time the remote hand held is triggered.

This unique module connects a 1 - Channel Remote RF system quickly to the Sound Board VEGAS The on board power supply connector provides power to operate the RF receiver directly and provide power to operate the Sound Board VEGAS all from a single 12 Vdc power supply. The board has wire terminal blocks for quick connection between the RF interface / power board and the SB VEGAS.

Hand Held Transmitter:
Type: RF radio(315MHz)
Transmitting Distance: 200m
Supply Power: A23 DC12V Battery
Encode: Fixed code
Momentary: Press-ON, Release-OFF
1 - Channel Soft Button
Expanding Antenna (2-3/4" long)

Receiver Module:
Type: RF radio (315MHz)
Operating voltage: 12V
Decode: Fixed code
Control Type: Momentary
Connector Cable and Header to Sound Board Input
Wire Terminal Blocks for quick set-up
On board power management

( Power supply for Interface not included )
( Sound Board VEGAS Module not included )

Click on image for a Closeup

Board Size:
Approx 2-5/8"L x 2-5/8"W x1/2"H

Setup Example - Power to Sound Board VEGAS
Setup Example - Remote

Application Example

This unique module will connect the RF 8 - Channel Remote system quickly to the Sound Board VEGAS. The on board power supply provides power to operate the SB VEGAS and the RF 8 - Channel Receiver all from a single 12 Vdc power supply. The board has wire terminal blocks for quick connection between the RF 8 - ch relays and the SB VEGAS.

A header connector on a 4" ribbon cable quickly connects the control pins of the SB VEGAS to the 8 - Ch Remote Receiver.
A set of jumper pins, allow the SB VEGAS to be placed into the Random, Sequence or Ch 1-8 playback mode.

An on board button allows the SB VEGAS to record sounds quickly without disconnecting the interface. The button also serves as a test function to playback sound and check the Sequence and Random board modes.
Board has power status indicator LED's and On anf Off power switch

Board requires 12Vdc @ 1.5 amp power supply

( 12Vdc Power supply for Interface not included )
( Sound Board VEGAS Module not included )
( 8 - Ch RF system not included )

Small board approx.
2" x 4" (107mm x 69mm)
with 5 - BNC video connectors,
9Vdc power supply socket

LED Status lights and
PWM servo connector

Information Document

Unique servo signal controlled electronic video switching system which provides clean and fast switching between 4 video channels to 1 channel.
System allows 4 video channels to be switched to 1 master channel, by adjusting the R/C transmitter joystick, or assigning a servo signal value from any R/C PWM signal controller.

The Video switcher board will switch one of four video input signals to a buffered video output line. The Video Switcher board is suitable for all standard CCTV type video signals.

Small board approx. 2"x 4" with BNC connectors for the video and 9Vdc supply socket and servo connector.
Video Switching is done by a solid state unit using a standard 4 to 1 mux under micro processor control. The processor also measure the incoming servo pulse and determine which input to connect to the video output.

System is excellent for operating 4 different cameras, and sending video signal from one of the 4 cameras out to a remote transmitter. Put full 360 degree vision on your robot, airplane, animatronic character, or setup a covert operation with remote control.

Servo Signal
Adjusting the input signal (ie the pulse duration) will alter the video input being fed to the video output. The led by the side of the input socket will light when that particular input is live.
Input 1 is pulse widths between 1.0 -1.25 msecs
Input 2 is pulse widths between 1.25 - 1.5 msecs
Input 3 is pulse widths between 1.5 - 1.75 msecs
Input 4 is pulse widths between 1.75 - 2.0 msecs.
Power needed: 9VDC at 250mA - 2.1, power socket-center positive. R/C receiver, Video Transmitter, Cameras and 9 Vdc power supply not included

Unique System allows you to hear and talk back to your props, puppet character as people interact with the puppet.

Portable Audio Sound System


Details Available Soon

System

Wireless Microphone Module

Details Available Soon

System

YouTube Videos of Animatronic
Characters using BPE Controllers

Animatronic Rabbit-1
Video Size - 2.3 MB
Animatronic Rabbit-2
Video Size - 2.0 MB
Animatronic Rabbit-3
Video Size - 2.4 MB
Animatronic Rabbit-4
Video Size - 2.1 MB
Animatronic Rabbit-5
Video Size - 2.1 MB
Animatronic Rabbit-6
Video Size - 2.3 MB

Animatronic Vulture
Video Size - 5.1 MB

Animatronic Plant
Video Size - 6.5 MB

Animatronic "SPAWN"
Video Size - 6.3 MB

Talking Pirate
Video Size - 8.4 MB

In addition to providing a constant expanding product line, Blue Point Engineering LLC. also has created a Custom Engineering Service to bring to life your own puppets or props, The professional staff at Blue Point Engineering can custom design and build the mechanical components, electronic control, lighting and sound effects needed for your puppets. Please feel free to correspond with Blue Point Engineering about your needs. The staff can put together an overview with hardware, electronics needed, item description, time lines, project costs, and services available for your project needs.

E-mail Questions to: Blue Point Engineering LLC. or call:
BPE Phone: (303) 651-3794 .... ( Business Hours M-F .. 8:30 am - 4:00 pm Mountain Standard Time - MST )

Animatronic Little Old Man
Head moves Left / Right and Up/ Down
Mouth movements sync to sound tracks
Arms Move Up and Down

Controller Automation
AutoTalk Board
Wizard Controller - R/C Interface Board
MP3 Sound Player

Power Distribution Board

Power Supplies - 9 Vdc.
Everything included to operate character

Animatronic Talking Head
Mouth movements sync to Manual Remote RF Controller

Controller Automation
Remote RF hand Keyfob controller
Wizard 12 Controller board - R/C Interface Board
Power / RF Signal Distribution Board

Power Supply - 12 Vdc Battery.
Everything included to operate character.

Other Features / Options available

Animatronic Meat Eating Plant Puppet
Plant moves left and right
Mouth movements sync to sound tracks
User programmable Audio Playback System


Controller Automation
AutoTalk Board
Wizard Controller
MP3 Sound Player
PIR Sensor

Power Distribution Board

Power Supplies - 9 Vdc.

Everything included to operate plant